2PCS Ender 3 Pro Glass Bed, Upgraded Tempered Glass Plate with Bed Clips, Ender 3 Build Plate 235x235x4mm for Creality Ender 3 Pro/Ender 3 V2/Ender 3 V2 Neo/Ender 3 Neo/3 S1/3 S1 Pro/5 Pro

Okay.. There are so many reviews and broad mixed emotions on these glass beds. Being this was my first 3d printer and first forray into the genre, I was completely unbiased either way, so this review will reflect the pros and cons. First off, the bed is nice. No flaws, was packaged very well as to prevent damage in transit and is a good value for the money. I didn't straight edge it to check for warpage, but I've had absolutely zero leveling issues. Next, let's talk about the only real issue I have with it. It's not enough to ding the stars, but still, it's pretty lame. You have to secure it with binder clips. To me, that's absurd no matter what. Why would you make a plate such as this that doesn't have a secure mount system, and one that requires the user to use clips that impact the print dimensions. Makes no sense to me. From there, the rest is all good. Printing on the textured side works fantastic for PLA, no doubt about it. Zero problems with adhesion, no glues, sprays or tapes needed. With that said, the slick side is even better! Whoops, did I just say that?! Haha! Yes, the slick side for me was recommended in one. of the FB groups and its been awesome! PETG, PLA, PLA+ are all filaments I've used and they all hold on for dear life. Until cooled off that is. But let me tell you, if you start on the textured side and decide to flip it, it's a real PITA to remove from magnetic bed base (if you have one on yours). It sticks with serious bite, but it's actually easy to pop off if you use Scraperite plastic razor blades or similar thin, ridgid plastic scraper. You just have to get between the glass and mag surface, and work your way around until you hear a slight POP. The it's released and you should have no damage to either the bed or mag surface. If you hear a crack and not a pop, you messed up lol. Using glass, you need to tweak. your temps a bit, but once you have everything dialed, it's an awesome bed surface. Can't see the need for PEI so far, glass has met ally expectations.

Same with a lot of other people here.. It was great for 2 weeks then nothing sticks, even when i heat up the bed real hot. 80Deg and PLA still doesn't stick anymore when it did at 60deg before. Cleaned thoroughly and still end up with filament floss when objects come loose. It's so frustrating especially after waiting hours and then suddenly all adhesion goes away. I have changed my review to 5 stars from 3 after they sent me a replacement plate. I use one pass of stick glue on the plate once a week (print daily) and the adhesion is strong enough that I don't use brim support anymore but the bottom of prints are completely flat. Adhesion is strong but can still be removed by hand without tools. FWIW, I have also adjusted my settings for a slower speed and hotter bed for the first few layers and that took care of warping. Now that I am using glue on the bed, I am increasing the print speed and the prints just stick. If you let the bed cool, the print will come off pretty easily by hand.

These glass beds are a big improvement over the stock surface. Both pieces were perfectly flat and gave my prints a smoother, more consistent finish. I use a bit of glue stick for adhesion, and it works great — I haven’t tried printing without it yet. When I’m done printing, I just pop the bed in the freezer for a few minutes and the prints release easily without any prying or damage. So far, no chips or scratches, and both glass plates are holding up really well. Overall, an excellent upgrade for anyone running an Ender 3. You get two solid, flat glass beds that make a noticeable difference in print quality and ease of use. Highly recommend!

There was a minor chip on mine, but its not large enough to cause an issue and its on the bottom of the plate. PROS * Amazingly smooth bottom surface for prints * No warping or other initial layer problems * Removal is often easier than with the magnetic plate (though sometimes prints get a little stuck) * Perfectly level build surface!! (much easier to level than the magnetic build plate) CONS * Adhesion isn't great * Using medium binder clips means you lose a little build area (not a whole lot) * Takes longer to heat up OTHER * Noticed yellowing of cloth after cleaning with rubbing alcohol, not sure what this is though it seems to be from the adhesion layer * Take care when handling, dropping this thing on the floor is a bad idea REVIEW NOTE: This might read a little more like a negative review for the magnetic build plate than a positive review for this plate, but that's just because that plate is a headache and a half and I needed to vent about it. This build plate makes it apparent really quick that the magnetic build plate is not ideal for 3D Printing in the long term nor for larger prints, for several reasons. (A quick review of the magnetic plate for comparison) The magnetic plate has a great strength: you just pull the bed up and prints peel right off! But it comes with a dire trade off: the build plate is very prone to indentations when removing prints. This makes it absolutely horrible to print on afterwards; when you have hills and valleys in your build plate, your initial layer will be nonexistent where the hills are. It's horrible, but it's easier to start out I guess? Anyway, the tempered glass plate has a few setbacks as well, but I'm convinced that it IS an upgrade and going to outlast the default magnetic plate bed (for several, several reasons). To really use this plate without those famous adhesion tricks (hairspray, glue) I set the initial layer speed low, I mean really low. 10 mm/s (yes, that's really low, but it works) and I set the initial layer temp to 80 C (I read this somewhere but can't remember where). This helps ensure the bed is evenly heated and the surface is properly 60 C or slightly higher. You could probably go a little lower than 80, but this is what I did. Now adhesion isn't as big of an issue, and I'm much happier when printing because I don't have to deal with the monstrosity that is the magnetic build plate. I give the magnetic plate 3/5 stars if its brand new, 2/5 if its been used, and 1/5 if its been used AND is demagnetized :)))) If your print is a little stuck even after its cooled, I found wiggling the snips that come with the printer (a godly tool that should be cherished) under the print and prying the print off works really well. The print should just pop right off.

Si adatta perfettamente al piatto di stampa , conduce il calore bene . Trattiene le stampe

Wanted to replace my existing hotbed cover with glass and this was a good fit. Fits my mega zero 2 perfectly. One side has a texture on it and the other side is completely flat no texture. Would recommend

I recently purchased the "Improved Tempered Glass Plate with Bed Clips" for my Elegoo Neptune 3D printer from Amazon.de. I received the product promptly, and after installing it on my printer, I am extremely satisfied with its performance. Firstly, the glass bed's dimensions (235 x 235 x 4 mm) fit perfectly on my printer, providing ample surface area for my prints. The tempered glass construction ensures durability and stability during printing. One of the standout features of this glass bed is its compatibility with PETG filament. When printing with PETG, the filament adheres securely to the glass bed, from 60 C in my setup . I typically run the bed at 65 degrees Celsiusfirst layer and then down to 60 for the rest of the print , and I have experienced excellent adhesion throughout the printing process. It becomes nearly impossible to remove the printed objects when the bed is hot, which is a testament to the bed's effectiveness. What I appreciate most is how the prints effortlessly release from the glass bed once it cools down. This eliminates the need for excessive force or scraping, resulting in clean and undamaged prints. The smooth structured surface of the glass bed also contributes to the overall print quality, providing a flat and even base for precise prints. I of course do not use any glue or hairspray. Just a clean bed and I clean it between prints . While I have not tested other glass beds for my 3D printer, I can confidently say that this product exceeds my expectations for PETG printing. It delivers consistent and reliable adhesion, ensuring successful prints every time. I would like to commend the seller for the quick shipping and excellent packaging. The product arrived in perfect condition, ready for immediate use. In conclusion, I highly recommend the "Improved Tempered Glass Plate with Bed Clips" for anyone seeking a reliable and efficient glass bed for their 3D printer, particularly for PETG printing. I am thoroughly satisfied with this purchase and would gladly give it a full score for its outstanding performance. Thank you to the seller for providing such a fantastic product!

Llegó muy bien empacando, además los comentarios negativos no se a que se deben, si realizan una configuración adecuada de impresión puede aprovechar muy bien la calidad del cristal, en ningún momento tuve problemas para despegar y pegar y no es necesario hecharle laca o algún producto de adherencia, se debe a la configuración de impresión para que se adhiera muy bien, ahora con el warping se debe a la velocidad de la impresión, jamás tuve problemas de esto llevo ya casi el mes y no he tenido problemas en nada, excelente cristal de impresión

Since it’s made of glass and therefore much more hard and brittle than the standard one you’re given you have to have the absolute most accurate precision when levelling your printers bed in order to avoid damage to the nozzle - something I learned the hard way.