Upgrade 3-Layers Filter System Smoke Exhaust Kit with 5000RPM Fan and Speed Control Power Adapter for All Laser Engraver 3D Printer Enclosure Tent Cover DIY (Ventilation Kit)

Ordered this enclosure because it was the cheapest option for a CNC machine without having to custom build everything by hand. The dimensions of the large enclosure is 30x30x35 inches, which fit perfectly for my Openbuilds C-Beam machine. I've been working on adding some custom parts to my machine so I needed it to be slightly bigger than what I currently have and this fits like a glove!The box this enclosure shows up in is surprisingly small, considering what is inside. Almost thought I was sent the wrong enclosure but no. It is just super efficient packaging.A word of advice because it took me a moment (too many IKEA builds), the lettering on the tubes are for Length, Width and Height. I initially expected it to be like IKEA stuff and certain pipes go in specific places but no, just stick the W pipes together and place it in the right orientation. Super easy instructions.There is a 3D Printed light bar clip in the box. I suggest adding the light bar and clips to the pole before installing it as one of my clips broke when I tried snapping it on. Thankfully it comes with straps that work too.Overall, this enclosure is going to allow me to use my machine without dust or chips flying all over the place. There are plenty of holes for wires or tubing for a shop vac or something similar. If you're needing an enclosure for a CNC but dont have the budget to build one, this will work.Just dont expect it to muffle noise much.

Plenty of room for my Resin printer, added the ventilation kit. Very little order when printing. Helps hold the heat in, holds a fre degrees better than the rest of the room, but the vent pulls most of it out

It works really well, but the fan is a bit loud. Also there is not place to buy replacement filters.

Purchased this to replace the fan on the cover for my engraver. Works even better than the cheap fan my cover had originally come with. It's quite loud though.

After buying this for a second time I realized that my old purchase didn't have two extra extensions, instead it was actually missing two extensions. The instructions weren't clear on whether the "H" pipes needed extension bars, but the new one is complete and fills out the fabric much better. Also, one of the new LED clips broke while I was messing with the new one, so I'd recommend using the velcro cable ties instead or in addition to the clips.

I have FDM and resin printers. This enclosure works great for both. I got a 4" inline fan designed for green houses and vent it out the window with a dryer vent in a sheet of plywood. I do the same for my laser with a 6" vent. So, I just used the same board. I leave a little vent unzipped in the front to help with air flow. No issues with any of my printers. I'm in a rental, and had to have a non-permenant solution. This works great. It is very light and easy to break down for transport, or storage.I started having print issues after a while, and put a hygrometer inside. The humidity of the enclosure is higher than the ambient of the room by 8%. This appears to have effected the filament. So, I have stopped leaving filament in the enclosure after printing is complete. I believe humidity from outside is making its way into the enclosure after I turn off the fan at the end of printing. My vent does have a flap, but it is not air tight. It just keeps the insects out. Not an issue with the enclosure, but it does necessitate a change in workflow. At the end of printing, I pull the filament and place it in my dehydration box, which I probably should have been doing anyway.

The heat pad only goes up to like 30 degrees at the 70 degree setting in only the center, THE POWER SUPPLY LITERALLY GETS HOTTER!! DO NOT BUY!!!!!!!!!

It's a good enclosure for your 3D printer. It's fire proof, too. Made with a sturdy frame and thick flame proof canvas. It has well built zippers that zip clear from bottom front to the very top rear. It has a see through window with Velcro attachable UV light filter for resin printers as well. It also includes two ventilation ports on either side and round ports on the front. It also comes with a foil expandable exhaust tube for connecting to filtration, a Velcro exhaust tube connector and the location to download and 3D print an adapter for a computer fan to use for exhaust. Assembly is pretty simple and can be done in about 15 minutes. It definitely cuts down drafts and improves print quality. It traps heat very well and the bed and extruder will heat up the chamber. The only thing it is really missing is being heated for polycarbonate and nylon. I have an Elegoo Neptune 4 in it and the filament roll is about 5mm from the top of the enclosure to give an idea on size. Their is about 3 to 4 inches on either side of the printer.