Gizmo Dorks PLA Filament for 3D Printers 1.75mm 200g, 4 Color Pack Multicolor- Blue, Green, Orange, Red

After reading the reviews regarding color accuracy, I was hesitant to purchase this pack, but I'm *very* glad I did. I've almost finished each of the four spools, and the quality has been excellent across the board. Additionally, Gizmo Dorks customer service was fast and helpful when I had a question before ordering. COLOR I'm not sure why there are complaints about color. My filament had strong color, which matched the described blue, green, orange, and red. In the review photo I've compared printed items to the authoritative color source-- Lego bricks. The orange filament is a slightly more yellowish tone than a "true" orange, but I also found the color to be more aesthetically pleasing than a bright orange. (Each of the filament colors also match the appropriate CSS color name, but Legos are always the answer.) PRINT QUALITY Excellent prints using an Ender 3 at 195 degree/45 degree hot end/build plate temperatures (bed adhesion, layer adhesion, and dimensional accuracy). No issues with filament diameter in any of the spools. TIP: store the spools in an airtight container (or zip-top freezer bag) with the desiccant pouches the spools shipped with. This will reduce the chances humidity will compromise the filament quality. CUSTOMER SERVICE I emailed Gizmo Dorks customer service get a copy of the Safety Data Sheet (SDS). I received a follow-up email almost immediately, and I received the SDS the next day. This was amazingly quick and painless compared to many other vendors. CONCLUSION I'll be switching over to Gizmo Dorks as my primary source for PLA filament. The quality is excellent, and the price can't be beat.

I read a lot of reviews on this filament and it seemed to me that there was quite a few negative comments. After using the filament myself, I felt the need to address those comments. 1). Color quality. I saw a few comments about this filament being dull and not vibrant. I did not find this to be the case. I liked the look of the colors and once they were printed they did not lose that appearance. The colors appear pretty much they way they do on the picture. 2). Filament diameter tolerance. I cannot speak to exact variations in diameter, but I can say the the filament appears pretty consistent. It fed into my printer without issue and printed very well. 3). Winding. Here was the one complaint that I can agree with. The filament is not wound with the same degree of accuracy and precision as most that I have bought. I can see where snags might happen. Now, saying that, I have not experienced any snags or tangles. 4). Quantity. It is four spools of 250 gram filaments each. It is advertised as such. I bought what was advertised and got what was advertised. I don’t understand some of the comments about the spools being small. I found it to be an excellent price for four different colors when my needs were small. If you need large amounts of a particular color, you should look elsewhere. 5). Print quality. I’ve bought filament from Amazon before and have had nothing but problems with it. This is not the case here. The filament prints out well and the detail is about what I would expect. Understand, I’m not a high utilization user. I print for fun. And what I find passable or good may not be in the eyes of an expert. I’ve included pictures because i think they will say more than I can. I bought this filament to make game pieces. It does this well. I’ve not found any uses yet for large prints. If all you are using this for is limited runs then you will be happy with this.

No jams or clogs. My printer likes this filament and it’s nice having a set of basic colors

UPDATE (5/5): 3.5 stars. My previous issues may have been with just the green roll of filament. I tried the 195° print temp and got slightly worse results. Went back to 210° with the blue roll and while the stringing is still present, it is significantly less than before. I printed the green filament on the standard spool holder for the Ender 3, but I put the blue filament on rollers in my custom made dehumidifier box. It's possible that the green filament had absorbed too much moisture (even in their packaging) and that was the reason for the poor quality. If I update this review again, I'll try the green filament after it's been dried out and see how it goes. Overall, not a bad filament. Great for larger less detailed prints, but lacks some quality for the smaller intricate prints. Original review: I use an Ender 3 V2 with standard 0.4mm nozzle. The two castles on the left used a 210° nozzle temperature (recommended is 205-230). Terrible stringing and some layers didn't adhere to the previous very well. Initial layer was at 200 with a 60° bed which seemed to work well. Castle on right was printed at 200° and the stringing was significantly reduced, but still there. I'm trying a 195 print now and will try to update of it works out. Colors are vibrant and the spools were well packaged with desiccant packets and vacuum sealed bags. Overall, it's not a bad price for 4 200g rolls, but I would expect the manufacturer recommended range would work for the most popular 3d printer. I'll update to 4 stars if I can get a good print playing with the settings.

Work perfectly in our toy box 3 d printer. Great assortment of food colors.

This is probably the easiest filiment I've used. I'm pretty new to 3d printing but I've used a few different filaments, and this gave me zero issues. I've only used blue and red but the colors seems correct. I got some warping on the blue box but not the filaments fault, version 2 was much better once I leveled the bed again. **Update** I went through all the green and yellow and this filament seems to like lower temps. I print at 195c hot end and 60c bed. The adhesion to glass seems to be not the best but a glue stick fixed that. The stock ender 3 bed gave better results. Definitely going to try buy a full roll of the green and some other colors.

Si necesitas colores variados para tus impresiones y no quieres gastar en carretes de 1kg de filamento, esta es una buena opción. De repente hay que estar pendientes de la impresión porque a veces pasa que el filamento viene un poco más grueso y se puede llegar a atorar (me pasó sólo con una de muchas impresiones, por lo cual no creo que sea un problema tan común). La adhesión entre capas es muy buena, la fuerza del material es buena. Los colores me parecieron muy bonitos. La usé en una Ender 3 Pro con 210° en la boquilla y 70° en la cama, fueron los ajustes que mejor me funcionaron para adhesión a la cama y adhesión entre capas, además de que da una pieza robusta y resistente. Sin duda volveré a comprar cuando se me acabe.

Very nice colour pla. Prints nicely

Very good and stable product

works

Ya llevo un tiempo usando este filamento en una impresora pequeña de 10 x 10 y me encanta como imprime, se me hace económico porque trae varios colores y puedes probar varias opciones.