JESLED Upgrade LED Flashlight Bulb, 12V 18V 3.5-24 Volt, 3W 247LM, PR2 P13.5S Maglite LED Conversion Kit for Ryobi Milwaukee Craftsman Lamp Torch Lantern Work Light, Maglight Bulbs Replacement 2Pack

Works great, definitely brighter than the original incandescent bulb. Would buy again.

Last year, my friend lost all his power for a few days. A tree came down and took out the power right in front of his residence. I quickly assembled all of the powered devices I could find to help get him and his through the next few days. I had a Ryobi flashlight with an incandescent bulbs, like something you'd find in the nose of the patient in the game Operation. Super-quickly, I ordered these replacement LEDs, and I think they came the next day, and because they were so efficient, they lasted far longer than the incandescent bulbs, even if this LED replacement isn't considered by many to be a huge improvement over brightness. That said, I didn't notice a significant lack of light. The replacement LED bulb seemed to do what it promised to do, i.e. provide a decent amount of light, while saving some battery life.

Much brighter, & whiter than the incandescent bulb it replaced. Not quite as bright as I expected but far better than what it replaced. Brought an old light back to life.

Purchased this to replace bulb in DeWalt 18v flashlight. I use this flashlight a lot and often leave it on for an entire work session of an hour or more. The light from the old bulb was somewhat uneven and faded as the battery discharged. This new bulb is exceptionally bright with a more neutral color temp (less yellow than the old bulb). It throws a wide and bright cone of light. The only issue is that it is more bright right in the center, but that can be a good thing when working up close. I don't see this as a problem, but wanted to mention it. I may buff the small lens over the LED to create a more diffuse light in the center. {Subsequent Note} - I spent some time with this last night. The bright, center spot is a result of the flashlight reflector cone and how high the bulb sits therein. If I lower the bulb, I get an even illumination in the cone of light. I will tweak this so the top of the bulb sits flush with the DeWalt reflector cone. Thus, this is not a problem with the bulb but more with the DeWalt flashlight. As mentioned, I don't see this as an issue, but wanted to be accurate as to this point. The bulb change took just seconds (a perfect fit for the old one), and I was blown away with how much brighter my favorite flashlight now is. I am very happy with this purchase.

worked great - no issues, nice and bright

Bought these as LED replacements for older incandescent Ryobi 18v lights. They are fine for the minimal investment. Maybe can find better, I am not comparing to others, except I have a 5+ year old LED in another older Ryobi, light, these are better. More detail; I do low voltage landscape lighting professionally & am pretty good at identifying color temperature of lights (Kelvin K rating). These do NOT look to me like the advertised "6000K Bright White". They appear to be more around 3,500 to 4,000K. This might be due to the Ryobi plastic lens, I did not test for color without lens. Personally, I much prefer the lower color temp, so I am pleased they do not appear as 6,000K. Attached 4 pics: Older lights these installed in, tree at about 100 feet, fence at about 300 feet, new style Ryobi with it's integrated LED at fence 300 feet. When 1st installed, beam was wider, but darker spot in center. The pics are after a 'trick' - I placed a regular galvanized steel washer between bulb & reflector cone. This sets LED further back into reflector. Results in a bit narrower beam, but eliminates darker spot in middle. Essentially allowing reflector to do it's job (keep in mind reflector was designed for a bulb with omnidirectional charateristic, not single LED chip). Can install 2 washers if narrower beam is desired -personal preference. 1 washer works for my intended purpose. Note last pic of new style Ryobi light, it Does have true 6,000K appearance - if you desire this, buy the new model light, or try other replacement LEDs. Overall, these are an improvement over original incandescent, paticularly for longer battery life & lower opperating temerature at minimal cost. Hope this info is helpful.

These did make my Mag Lite flashlight much brighter, but I get odd flashing from time to time. To prevent that I have to adjust the lens, but it still happens.

I bought a pair of these bulbs to upgrade two older 3-cell Maglites. While brand new LED Maglites may be slightly brighter, these replacement bulbs are far brighter than the original incandescent bulbs. Good coverage, too. I had bought another company's flashlight LED bulbs a while ago. These are much better and I would recommend these if you too, are looking to do an upgrade of an older flashlight. Perfect fit. And less expensive than buying new 3-cell Maglites !

Received these LED light bulbs through fast delivery from Amazon. Installed them on 2 Ryobi 18 VDC flashlights and compared the illumination vs. original incandescent bulbs. These LEDs emit withe light, much brighter than the originals. Light cone is focused to a point in space that seems to be closer than the original bulb, making the overall viewing distance somewhat shorter, but much brighter. It will work best if you use this as a worklight for short range, not a search light for distance.

Lo compré para reemplazar el foco original de una lámpara Milwaukee de 12v y quedó a la perfección, da buena luz y no se ha fundido con golpes fuertes

se quemo rapido, casi genera un incendio en mi casa, deje la lampara fucionando para ir por herramienta al regresar estaba la lampara humendo y encendiuda afortunadamente la apague antes de llegar a la bateria de litio

Los instale en la linterna y ninguno de los 2 funciona, no prenden le puse pilas nuevas y tampoco funcionan