Nilight 20Inch 126W LED Light Bar Spot Flood Combo Driving Off Road with Front License Plate Mounting Bracket Wiring Harness for Trucks Pickup Car SUV ATV UTV 4x4 Van Camper, 2 Years Warranty

The media could not be loaded. So far I am extremely impressed with this light bar. There are larger ones, but I can't imagine where or when you could even turn them on... I can't turn this one on except out driving in washes and dirt roads at night, hopefully with a forest around me or I'm going to blind everyone for half a mile. See video for details.I installed this light bar in about 20 minutes on my new Ranch Hand bull-nosed front bumper, after reading reviews and specs to be sure it would mount directly to the bumper light mounts with no adapters or brackets needed, and indeed the holes aligned perfectly. Some reviews have mentioned that the brackets arrived bent, and that they had to be bent to fit - partly true, but they didn't get bent in shipment, they were identical in their "slightly too narrow" aspect. This is intentional, so that when you slip them over the part that attaches to the light bar, it is held tightly in place as you stick the screws into their holes. So forget that whole "bent in shipment" thing, they are made that way on purpose.Unfortunately, the bumper had big holes in the light mounting tabs, so I did have to go to Home Depot to get some big washers, so add 20 more minutes for that side trip. But that's not an issue with the light bar, more like an incompatible bumper that needed a little help to be securely affixed. Your bumper or mounting location may work just fine without any additional hardware.I was having a new radio installed, so I had the radio installer at Best Buy pull the wires from the new Nilight dashboard switch ($10, also from Amazon) and connect it all up with soldered connections and heat shrink tubing like he did for the rest of the cables... That would have added a couple of hours if I had done the wiring myself - but since they had the dashboard apart anyway, this just made more sense to me. The zip ties in the photos were temporary until the wiring job was completed, now all wires are secured with black metal wire guides along the back sides of the bars. I did have to drill a hole in the bumper metal to route the wire - no big thing, and the Best Buy guys had a black grommet which fit perfect. Pros over there.You have to have the LEDs on to align the light bar correctly - my best eyeball guesswork was making a big bright spot on the ground right about where the low beams hit the ground. Adjustment is simple, if you have the right screwdriver (varies depending on the bumper and mounting location, what all is in the way, etc). Alignment took 5 minutes or so. The light bar gets quite warm to the touch as expected, but at no point was it too hot to touch during the adjustment operation. Hot but not enough to burn you or be a hazard.I very much like the arrangement of the 6 right and 6 left LEDs being flood focal length reflectors while all of the rest are long-throw spot focal length reflectors. You can see the difference in some of the pictures, and in those from other reviewers. You get a perfect mix of nearby and "way down the road" illumination. Check out the pictures and video - this thing looks great, works great, had excellent pricing for the performance, and is obscenely bright. Wow. Highly recommended!

(Update 05/12/19: 6 months ownership) Bar still intact and fully working, not a single problem so far. I’ll keep this updated if something happens.Ok. I rarely write reviews but I think this is gonna help a lot of people. I feel like I have to warn you guys about a couple of things.1st- This bar is AWESOME for it’s price. Can’t beat it. Period. Don’t expect to turn night into daylight, not gonna happen. Helps on narrow roads with lots of trees. If you have really strong high beams, this will increase visibility and help by, at the most, 10% on open roads (with high beams on). It shoots light everywhere. Does not have a super defined beam.2nd- MOST IMPORTANT : BUY RTV SILICONE AND SEAL THE PLASTIC WHERE IT MEATS THE METAL. It will extend the life of your bar, perhaps until the end of the warranty or more. The reason people are giving low stars and bad reviews is because the original sealant is CRAP. Water WILL get in and damage it. Plain simple. Put the Silicone tube nozzle on the space between the metal and plastic and PRESS IT. Make sure there’s no gaps or holes.3- Really surprised by the sturdiness of this bar. Strong metal with a very high end felling to it. My mounting kit came just fine and installing didn’t take long, although there’s no manual. Put it on youtube and there’s videos on how to install it. No brainer. Came on a big box with lots of paper to hold it in place.I’ve been through heavy snow, behind cars shooting salt and ice on it (it stays low as you can see), been through car washes (soft touch and touchless) more then 10 times now, sprayed power wash gun directly on it (don’t recommend) to test the RTV and it held like it should. Still going with all LED’s working.PROS: Cheap, sturdy, bright enough for it’s price, easy to install itCONS: original sealant is terrible beyond words, make sure you do the job they didn’t do it. RTV the thing and you will be fine.If anything unusual happens I’ll be back to update this review. I’ll add more photos and videos some other day.