Universal Aluminum Grooved Magnetic Jack Pad Jacking Puck Pinch Weld (Slot Width 0.39 Inch) Frame Rail Adapter for Vehicles (Qty 1, Red)

This works perfectly for my 2020 jeep Grand Cherokee, fits the pinch welds perfectly and allows me to use my floor jack without issue.The magnets might work too well though. On multiple occasions I've lowered the jack and forgotten the jack pad is still attached to the car. On the plus side, they hold on well enough that Ive found the pad still attached being the front wheel after a 700 mile road trip in the middle of winter driving through slushy snow half the time.

Forgot I was using it and it remained magnetized to the car for a couple days' travel until I saw it (bright red) and removed. Nice strong magnets!

I had a hard time tracking this information down, so I'm writing this review with my experience and knowledge. I have an Audi Wagon (B8). If you're going to get this, you need the 0.39" wide one, NOT the 0.55". Assuming your pinch welds are not damaged, these fit quite nicely. There are a few places on my Audi where the rubber covering on the pinch weld seems slightly larger (I'm assuming damage) and the 0.39" puck is too small to fit over that portion, but the damaged area is small and I can place the puck just above or below it without issue. If you go with the 0.55" wide puck, you'll find it's way too big and I didn't feel comfortable with that version. The 0.39" puck fits perfectly on the pinch welds in front and back. Bought 4 in total.

I left the last one on my wife's car after changing the oil, it didn't stay on. This is the replacement. These are great when you want to lift on the pinch weld.

I used these to jack up my daughter's 2015 Toyota Camry for me to do her brakes. They're great...the orange color is useful to help remember to remove them (yes, I'm human lol) and the vinyl-ish material that the pinch weld rests in is great to help protect it from damage. The magnets aren't incredible, but they hold sufficiently for the job. It is incredibly helpful to be able to place these on the vehicle before lifting your floor jack, and have an easy target to point the saddle towards. As always, NEVER get under a vehicle with just a floor jack...use jack stands with a pin lock mechanism, and only use the jack for initial lifting and additional backup support after securely setting the vehicle on the jack stands. Safety safety safety. Cheers!

This is a perfect tool to use when using a jack on your car where the pinchwelds are. This also prevents damage on the bottom of the car by the jack. I use this on all of my family cars I service. 2016 Dodge Charger, 2013 Toyota Venza, 2020 Honda Civic, 2013 Dodge Advenger. I will be purchasing again.

This jack puck works as advertised, but the magnet needs to be stronger. Small problem really.

Does what it says in the product description. Sturdy construction and overall it's nice to not have to stress about jacking points anymore. However, I must say that I only came here to review this thing to vouch for the magnet portion of it after it proved its effectiveness.I had used this to jack up my car and do some quick tire work. Took the car around the block for a spin to make sure everything was settled and tight. Then later that evening I had gone to the store for a grocery run. When I parked the car back in the garage I realized that I had forgotten to take the magnet off of the vehicle when removing the jack. Sure enough, it hadn't budged an inch from where I had placed it despite multiple trips. Something to look out for in the future, but nice to see it work well.

A high quality jack pad, but it only works if your jack points are in good condition. If the sill seams at the jacking points have already been damaged (or they are in good condition but plastic covered), this pad won’t fit. If your jacking points have already been damaged, find someone with an air hammer to get them back into shape.

Works great on our Toyota RAV4 but does not fit my Honda Ridgeline.

Great product, can be used on many vehicles

Initially, I used this with a 1.5 ton jack which had quite a small saddle (the part that's in contact with the vehicle). When I jacked the vehicle up, due to the movement of the jack, the adapter shifted on the saddle and it looked as though it was going to skid off and damage the sill, so I lowered the jack immediately.I since changed the jack for a 3 ton one which has a 3 inch saddle. The adapter sits comfortably inside that, and is now flat, metal to metal, so is very secure.The adapter is very sturdy and looks professionally made, has no rough edges and looks to be made of quality materials. The magnets are sufficient to hold it firmly to the metal weld without it being difficult to remove.As others have found, it's very easy to forget to remove the adapter (I have the black one), as it's almost invisible when under the car.I would highly recommend the adapter, but please take note of my warning about using this with a smaller saddle, as it could cause an accident or damage to your vehicle if it slips off.

Great