BushwackerTrail Armor Rear Corner Covers | 2-Piece Set, Black, Textured Finish | 14001 | Fits 1997-2006 Jeep Wrangler TJ with Bushwacker Pocket Style Fender Flares

Nice finishing touch

The media could not be loaded.  I installed these with the Rubicon Rock Rails on my 2015 Jeep Wrangler Unlimited (4-door). The complete install video is below.These look like factory, and will go well with any other Bushwacker fenders or trail armor.I only have the 2015 to go by, but there was no cutting or drilling required, and with the screws and the rails holding it in place likely the 3m Tape would almost be unnecessary.My method of install does not match the instructions, but I think you will find it easier. The combination of Rails and Guards keeps small rocks from lodging in the rails and really scratching the paint. The application of 3M Paint Defender makes sure anything that does get behind the guards won't buff or scratch that paint.I know the Poison Spyder Armor is popular, and it does cover more, but it rusts, and it requires drilling. This was a better solution for me with the rock rails.Rugged Ridge's version in mattes is awful. Don't buy those. They scuff, and don't stay matte, and are a lot thinner material that offers no protection.

This is a great kit whether you're using it for overing up blemishes on the corners or just want it for a different look in general. Installation is quick, but I'll lay out a few hiccups you may run into:1.) Make sure to buy the kit that's appropriate for stock or the bushwacker-style fenders. They're shaped differently and won't line up correctly with the wrong fenders.2.) The wiring harness connecting the passenger's side tail light is significantly shorter than the drivers side, so it's not long enough to pull through the hole and disconnect. You have to accesss it from under the car which is easy; there's a plastic or rubber panel at the end of the wheel well with a flap that comes loose ans you can bring the harness down from there and unclip. Easy, but keeps it from being a 0 dirt job since you'll have to be on your back if you don't have a relatively high lift.3.) Wash the corners areas and dry completely befor applying.4.) Do a test alignment before peeling the tape layer to get an idea. From there, align the holes first before pressing down becausebecause the automotive tape is very sticky and bonds that s moment. The driver's side is harder to line up some you have the gas cap holes as well on the side. I had success when i did gas cap homes first then lined up the back tail light and license bracket ones. 5.) It comes with clip-in adapters for the license plate screws. Make sure those are in the box before even starting.Included a before and after pic. I really like it. The armor across the tailgate is from rugged ridge.

This stone guard came undamaged and fit perfectly. Just be sure you have it pretty close to where you want it when you press it on. I had to rub out one end that didn't seem to want to really glue down well. But once I did that it stuck really good and has remained in place for months so far. I am happy with this purchase and was amazed how well the tape really holds. Looks great also.

I purchased these to cover a small dent. I also purchased replacement taillights and together it looks sharp. It is plastic but looks durable. Comes with 3m adhesive and has screw holes molded in for the tail lights to go in. On the driver side, the armor has molded holes for the tag. So, not only does it 3m tape, it has screws to hold it in. I can't say enough how good this looks. I am really proud of how it turned out! I would recommend to a friend. They really are a good deal.

I had a small dent on the right rear corner of my jeep. I had it rollered out as much as possible but the dent was still visible. I put the Bushwacker corner panels on to cover the dent and to add a little flare. They were easy to put on in about an hour and they do look good. Just make very sure that you have the corners exactly where you want them because when that 3M tape contacts the surface of the jeep it is pretty much permanent.

Drivers side fit perfectly, passengers side was a bit more tricky, once the lights were bolted back on, passengers side had a gap at the top, filled it with some black sealant caulking and that did the trick. Would recommend sealing the 3M tape before tightening the lights back on. Otherwise they look kick ass.

I received these , and they look about the quality of the plastic on the side of a Chevy Avalanche , beautiful today and it 3 years would be faded and gray . The install seemed simple , however if you don’t have the bolts for the pinch weld , you will have to go purchase them as it did not come with them . I returned them because of the lack of bolts, the life span seemed it would be short , the adhesion while 3m , would be something I’d have to worry about coming undone or needed to be reapplied later down the line . I personally just thought for 100$ more , I could purchase something that bolts on , and separate step guards that would allow me to not have to worry about them down the line . While I am sure this would have looked sharp , I do not believe for the price , that they are worth what they are asking .

very pleased with how easy it was to put on the jeep and the stickiness is amazing, there was one spot where I had to apply a little bit of two way tape to keep it down but it held up well. looks great on too.

Fits like a glove and it look great!!!

Hubby is pleased and easy to install and he loves the look of them.

Ad did not say what model the Jeep was for. I thought it was for a JK. I returned the item and received a very fast refund!

Hood piece does not fit all the way to the edge on the hood. Contacted the seller with pictures but no reply back. For the price this is a cheap item.