6 Pack-10ml Ink Syringe with 16 Ga Metal Distribution Tubes and Soft Plastic Tube Suitable for Glue Application,Liquid Dispensing and Measuring, Pet Food Feeding,Refilling Ink Cartridges or CISS

I have to flush my dog’s friggin prepuce (don’t look 👀), so I did a little modifying by cutting off the tip of the applicator since I’m flushing quickly. Was easy to modify since it’s a flexible material. I was worried that the attachment would pop off because of some of the reviews, but honestly, it would take a lot to even pull it off. You just have to get it on there real good. I added a picture to show it correctly applied with a tight fit. I’m a nurse and used to luer locks, but this holds together just as well. Which is good because I for the life of me could not find the lure lock version of this on Amazon before I decided to give this a go. Suction worked correctly to draw up all 10ml of liquid and it was nice and inexpensive. Would buy again. The picture is of my modified version of applicator. It comes much longer.

Syringe Suitable for Glue ApplicationMy first use of this syringe was for a 3/4" maple board that had split apart lengthwise the last 8" or so. Holding that split apart by 3/16", I filled the syringe with Titebond wood glue (easy to do), stuck the smaller (steel) distribution tube on the applicator, and filled the crack with glue by pushing the plunger inward. Used dental floss to wiggle the glue down until the floss wouldn't go into the crack any further. Clamped the cracked/glued maple in both directions and cleaned off the excess Titebond. Worked like a charm!The applicator syringe is simple to clean. Remove the distribution tube. Wipe off the syringe end, dip it in water and fill it. Squirt that water out and repeat as necessary. When it's clean, install the tube and push water through it until it comes out clean.

I used these for re-gluing the loose paper covers onto expensive binders by sliding the 'needle' up romt he bottom and down from the top between the paper and the cardboard. Because they're so long, the needle goes way inside there with no problem. I do this from the top of the binder and the bottom in order to reach the entire area I want glued, squeezing out some glue as I withdraw it. It works great. Previously, I had been slicing open the paper along the spine, gluing it, then I had to use tape to seal it back up. This way, I need no tape at all which is far preferable.I think they're for "one use only" but I reuse mine multiple times with no problem. I just rinse it out with hot water each time.For glue, I've been using Elmer's white glue that I water down with hot water to make it almost as runny as water. That way the glue can flow through the tip. Glue that's any heavier will not work in these syringes, but watery glue works just fine. I originally used fancy very thin cryo-acetate glue which works fine but is pretty expensive and is really not necessary -- but that also does work. I'm very pleased.

While not the nicest syringe it works pretry good for longer fountain pen cartridges to get to the very bottom. They feel like they don’t have great suction but they do function.

I use these for my aquariums and hydroponics and they work great. They are sold as single use but I use them repeatedly.The metal and flexible tips are nice options.

Work great do what they are supposed to do

I am giving 5 stars even though I could not get a good reference for the size of these and I could not use for intended use but that is not bad on the product. I think the product description would have been nice with comparison images for those of us who don't understand gauges of needles, again not the product fault. I searched all over before buying these though and all of these things look the same size when it is the only thing in the picture or the same picture for all sizes.I am keeping because I feel like they could come in very handy for what I did not buy them for, which was for adding fluid and removing air from my sand art.I had purchased special syringes for this before but of course I could not find them now that I wanted to use them so I ordered these. These will not work for that. Don't buy for Sand Art.The gauges of these are really thicker than they look in the pictures on the page and the blunt tip does not go into the seal of the sand art. Of course the same day these arrived I found the ones I bought originally for more than 4 times the amount but I guess they are just no on Amazon yet.Long story is I am keeping them as I am a crafter and I know I can use them for something, but you can see how thick they are next to a pencil if you are looking to insert into a small space.

Bought these to use for removing air in and topping off my snowglobe tumblers. Easy to bend with a small pair of pliers to get the angle I need. Durable and you get several for the price.