Planet WavesAuto-Trim Tuning Machines, 6 In-Line setup, Chrome, one size

Se los puse a mi Guitarra eléctrica Cort X100, le quedaron perfectamente, No se tuvo que perforar la madera ni nada, la estabilidad de la afinación mejoró muchísimo, se nota esta mejora de la estabilidad de la afinación al usar la palanca de tremolo. Éstos Locking tuners D'addario son tan buenos como los locking tuners de marcas como Gotoh, Grover, Schaller y otros, son de muy buena calidad, y como ya lo he dicho varias veces, la estabilidad en la afinación mejora por mucho.

Best upgrade I've bought so far...Quality of my guitar experience went through the roof!!Things to know about me1. I'm new to guitar so I completely SUCK at changing strings and hate doing it2. I'm older-ish and have other time commitments outside of guitar (I'll never rival EVH)3. I have four guitars and the strings are generally changed because I feel I need to practice changing them and not from wear4. the acoustic guitar may make the sounds of God, but the unwound strings are what Satan brought to the design meetingNo amount of YouTube will get me confident in changing strings because -without unnecessary changes- I just don't go through them very quickly. And when I do, the time lapse would show me aging LOL. Then I saw this product and I decided to take a chance as it seemed the worst was I may have to enlarge the post holes which is pretty easy. Sounds easy and who doesn't like new tools?Note: product comes with ZERO instructions so what follows is my experience for a 2020 Squire Affinity Stratocaster and a 2020 Epiphone Explorer...Remove old new strings. Removed the stock tuners (loosened by hand) and noticed the D'Addario's have a tiny screw at the back not present on either the Affinity or the Explorer. So I installed the tuners -posts dropped right in easy peasy- and tightened with a 12mm socket then predrilled rear screw hole (Affinity only) using 1/8" bit through screw hole. I think if you kept the collar tight you wouldn't need the screw but it may come loose over time due to tension (testing on the Explorer). Repeat 5x then restring guitar. The moment of truth... insert string -low E- into post hole, remove slack and tighten locking knob to hold string. Begin winding and notice gets very hard to turn as if cross threaded. Kept turning key...SNAP! IT CUT THE STRING! Immediately becomes easy to turn key. Repeat 5x, Tune to pitch.OMG, I love them. Why aren't these or similar standard on all guitars? It made 1/3 of my accessories unnecessary. I'd pay for them... in fact I did, because I immediately went back to Amazon and bought 3 more sets for my other guitars. Great outstanding product and now I don't fear needing new strings. Will update in a few days once other sets come and I install them (one more 6-inilne and 2 are 3+3 so may do a review there too). Thanks for reading and I hope this helps you decide one way or the other but I'd bet you'll love them too. Adios.

Nel corso degli anni ho montato diverse marche e diversi tipi di meccaniche autobloccanti, sia vintage che moderne.Queste in assoluto sono le migliori.Da subito hanno tenuto perfettamente l'accordatura senza nessun tipo di gioco delle parti meccaniche, cosa che, con quelle montate in precedenza, spesso capitava.Le ho montate su un'Ibanez e ho dovuto solamente smontare le vecchie e montare le nuove.Unica pecca sono le viti in dotazione che sono eccessivamente lunghe e apparentemente poco robuste.Una volta montate è sufficiente passare la corda nel foro, opportunamente orientato grazie al pallino presente sulla parte superiore dell'alberino, fissare la vite posteriore e girare la chiavetta. La corda viene tagliata automaticamente mentre va in tensione.Una volta che le corde si sono assestate non si scordano per molto tempo, anche usando energicamente la leva ed i bendings.Consigliatissime!Prodotto arrivato nei tempi previsti.

Takes a few days of playing to break after installation.. but after that it's rock solid tuning stability

compatible con ibanez rg721 sin necesidad de hacer ninguna modificación.para encordar, la bolita plateada debe estar mirando hacia abajo, a la entrada de la cuerda.al girar se coloca y se corta el sobrante.si no se mete la cuerda de ese modo, no llega a cortar y se queda mal posicionada.