DOME GLASS Galaxy S20 Screen Protector Full HD Clear 3D Curved Edge Tempered Glass [Better Solution for Ultrasonic Fingerprint] Installation Tray by Whitestone - Two Pack

So this is a more complicated install than normal peel and stick screen protectors. I've installed many on various phones and haven't had to use loca before. My first attempt, everything was going smoothly until I realized I installed the screen with the wrong side facing down. My second attempt, the loca dripped droplets outside of the large pool as I was removing it. I decided to clean that up and try again. 3rd attempt, the pool of loca somehow ended up off center, so instead of letting it sit there for 100 seconds per the instructional video, I tilted the entire assembly around until the loca spread to the entire screen. Followed up with the UV light and everything worked out.I would say if the loca drips elsewhere while you're removing the bridge, you don't need to start over because it will eventually spread out under the glass. After the curing process, the screen is great. I replaced my previous screen protector because it had the small circle for the fingerprint scanner and that was super annoying.5 stars because the product works if you're not having a bad day with the installation.

If you follow the instructions it will turn out great. This is the 4th one I've put on for 3 different phones. I highly recommend a youtube video on your specific phone as the written instructions can be hard to follow. But if you're patient and follow along, it will turn out great. The edges over time may start to look like spider webs because of the adhesive but these are the only glass screen protectors that not only fit the curved screen perfect but also work with the under screen fingerprint scanner that actually works. Don't hesitate to purchase.

BUYERS BEWARE!I spent $50 on this protector because of the reviews and I am VERY disappointed in the quality and response time of the CS team.The kit comes with 2 protectors. The install is fairly easy after watching the video, that is the only positive thing I have to say.The first screen cracked within the first week, along with having the sides chip off out of the blue. I figured it may have been something I did wrong.The second one did the same along all of the edges that you can see in the picture. The glass is literally falling apart and chipping off. I've had glass shards flake off in my hand multiple times. The protectors are THINNER than any other glass protectors I've used, which clearly makes them very brittle.So, having paid $50 knowing these had lifetime warranties, I decided to do a warranty claim...WHAT A JOKE!!You have to PAY $10 to warranty ONE single replacement screen. Seriously????? I've never had to pay for a "warranty" replacement screen with any other company, EVER!!Not having much of a choice, I paid the $10 for a new screen. It took them OVER A MONTH to get the replacement to my home. I'm beyond disappointed that I've wasted this much time, money and effort on something as simple as a screen protector.

This is an edit because of new information..I screwed up the first attempt. After I PROPERLY installed number two, I was trying to get the adhesive off of number one. I was man handling it and using a plastic scraper. I heard a CRACK!.These things are INDEED TEMPERED GLASS. I had written that I wasn't sure. Now I am sure.Regarding some reviews I saw claiming that these "Don't last". Of course anything can happen. But I do have some experience with these things. If you install it correctly, and if you're not a mechanically adept person I can see how you may not, it WILL NOT act right.If you didn't get a 100% coverage with the adhesive, and then cure it properly afterwards, AND if you didn't center it right, AND, if your case isn't compatible with the glass, it won't work right.My first attempt with this kit was bad. I moved the glass before it cured. So when I put my Otterbox Defender back on, it pushed the glass away from the screen and it wouldn't sit back down after that.So you see, if you get it right, it's FANTASTIC! If you don't, it will let you down. But you can't expect it work right if you don't install it right.I researched this protector for months. It is considered to be THE VERY BEST SCREEN PROTECTOR YOU CAN BUY. I AGREE WITH THIS CONCLUSION. And I am far from afraid to leave a bad review.Now for the first bit of the review..................I can't speak to the fingerprint reader as I don't use it. I kind of thought, "Sure! Let's give FascistBook and Goofgle my finger print along with everything else they have and sell about me. A great joke yesterday was sent to me by Spoogegle. They have a cell phone service now. Get this. They're actually bragging about how they monitor your privacy. Is anyone else just a tad tired of left wing radicals looking you right in the eye and lying to you? Sorry, the screen protector. I should start with the fact that I had one before on my previous phone. It came with two SPs. The first got smacked and it shattered but stayed stuck to the phone. When I peeled it off the phone was pristine. The second was the same. I dropped the phone right on the corner and the SP shattered at the corner. Again, I peeled it off and the phone was immaculate. I failed to buy another and I dropped a heavy object on the phone. Well, only a few ounces, but it was steel and the screen broke. Failure to get another Whitestone cost me that phone. So the next phone, a galaxy s20 at the time had no Whitestone available so I let the salesman put on a film SP. I hated it. It was all scratched up and peeling off where the selfie camera is. I just got the Whitestone kit before the weekend. One thing seemed different. This one doesn't seem like glass. It really feels like it's plastic. I saw another review saying the same and I wrote a comment saying that it's just so thin it can bend but it is glass. Now I'm not so sure. But today, the SECOND attempt is Beautiful. The first, well I used a spot on the counter that wasn't level enough and the adhesive started running towards the right hand side. After the 100 seconds it still didn't spread all the way under the "glass" so I tried pushing on it. DON'T DO THAT! I shouldn't have because I moved it on the phone a tad. It ended up looking nice when it cured, but when I put my Otter Box Defender on it raised the SP up at the top and after that it wouldn't sit back down. It turned out I made it go way off center. So I peeled it off and started over. I made sure I had a very level spot on the counter. Folks! This part is SUPER, SUPER important. This time the adhesive did what it was supposed to. I pushed down on the bottom of the frame (AS IT SAYS IN THE INSTRUCTIONS. IT TILTS THE WHOLE FRAME AND PHONE AND ALL UP ABOUT 10 OR 15 DEGREES) and waited until the glue was EXACTLY in the center of the phone. Vertically and Horizontally. I pulled the doo-dad and let the SP fall and in a bit over 100 seconds the adhesive had spread out perfectly. Don't watch it for the last minute or so as your perception of time gets wonky and you'll think it's not going to spread out correctly and you'll get impatient and do something dumb like push on it. It did though and then I turned on the fingernail dryer. (The UV light) the bad part about the light is that you're supposed to let it go twice for 60 seconds each time. The trouble is, the light only stays on for fifteen seconds. Not a huge deal of course. It is kind of amazing though how it works. Before the light it's very watery. Then it just sets up. Don't worry. If you need to, the SP will peel off very easily without leaving ANY glue behind. Now, is it really glass? I'm not sure. It looks great. The phone works exactly like it did without the SP. And I'm going to assume that it may protect the screen even better with plastic as opposed to glass. (That's IF. .. it is plastic.)Time will tell. If it starts getting scratched, I'll know it isn't glass. The last couple DID NOT, I REPEAT DID NOT get scratched. I was extremely happy with the last kit. Let's all hope it's still glass. Installation. Your best bet is to learn from my mistakes. Follow the instructions. They say to read through said instructions a few times and make sure you understand them. Trust me. It's very easy to screw the pooch with this one. It's also not that hard to get it right. But you MUST follow the instructions. Use......I am very happy as I was accustomed to the crappy film the guy at Best Buy put on the phone. Now my fingers just glide over the screen and everything is so incredibly clear now. Just like the 24 hours I just went with NO Screen Protector. Don't get the film if you can avoid it. These things are awfully expensive to be slapping something on right away that drops the image quality down by a fairly large amount.

Finger print reader works great. Feels like there's nothing on the phone, excellent oleophobic coating. Excellent touch sensitivity. Adhesion has been great for half a year. I have not tested removing it.Only downside I could think of is that without a case, the protector leaves a bit of a gap around all edges of the glass which might make it easier to catch on something and rip off. With the case I use, it ends up fitting better however. Your mileage may vary.The installation is pretty tricky, significantly harder than other screen protectors, but it's absolutely worth it for what you get with UV curing.

Istruzioni praticamente assenti

Procedure is complex but quite understandable. In first attempt though, glue was way less than needed and a large portion of screen had no glue underneath. In second attempt, the glue was still insufficient and one corner is left unglued and the this part of protector is being removed slowly with accumulation of dust etc. So much money for this crap!!!Finger print works.

To be honest, I was pretty skeptical whether such a high price was justified. After installation and a few days of use, I will have to say it's the best protector I've owned. It fits perfectly for the S20. The installation is not too difficult as long as you follow the instructions and ensure you do it on a flat surface. I will have to say the finger print scanner isn't 100% accurate, it's more about 80% with the glass on. This is probably the best you can get.. I've tried a different protector beforehand and the fingerprint did not respond at all. The glass is super thin and does not give off the appearance of a screen protector (blends in fairly well with OEM glass) unlike many other products.

Ich hatte bisher auf jedem Smartphone Display (früher) Folien oder (später) Glas als dauerhaften Schutz. Die Anbringung war meistens fummelig und selbst mit zunehmender Erfahrung blieb immer(!) mindestens eine Luftblase, eingeklebtes Staubkorn oder eine nicht klebende Ecke übrig.Was beim Whitestone Dome Glass anders war: der hohe Preis, die komplexe Installation inkl. Aushärtung mit UV Licht und ein absolut makelloses Ergebnis. Keine Luftblasen, an allen Ecken fest, kaum zu sehen und fühlt sich beim streichen mit dem Finger an, als wäre nichts drauf. Der Ultraschall Fingerabdruck-Sensor unter dem Display funktioniert. Dazu habe ich die Fingerabdrücke neu registriert, das braucht zur Erkennung dann eine etwas präzisere, längere Auflage des Fingers, bzw. mehr Druck. Da ich die Funktion aber nur selten brauche, kann ich damit leben. Dringende Empfehlung: YouTube Video zum eigenen Handy-Modell ansehen, Zeit nehmen und in Ruhe jeden Schritt der Anleitung befolgen.Verdammt, die Dinger sind teuer, aber das war mein High End Smartphone erst recht.Aber ein super Produkt, Danke dafür.