FLEXISPOT CylineE Electric Standing Desk Frame with Round Legs, Height Adjustable Sit-Stand with Memory Control Panel and Anti-Collision System, White

I have now had this product from Flexispot for a few weeks using it virtually everyday. I have been greatly impressed by the quality of the components. They are solid and of a heavy duty metal construction. They are also nicely finished and look good. Very solid once put together. There is very slight movement when the desk is at my standing position (114cm), but this is minimal and of no consequence if you're using the desk for it's purpose i.e. an office desk for IT kit. I had no issues putting the frame together and found the instructions more than adequate. The most difficult part was trying to align the top of the frame legs with the table top, but this was helped by pre-drilled holes and just required a little patience. My desk was delivered with a two pin rather than a three pin plug cable for the motor. However, I contacted the supplier via Amazon email/message centre and was impressed by the speed of their response and they sent a three pin plug cable immediately with no fuss, which I received within 2 days. So from that their customer service was also very good. I can only speak from my own experience, but the desk is excellent value for money (could have spent a lot more for something of similar quality), and does the job. No hesitation in recommending.

I am really impressed with the quality and how quiet to use this desk is. I had originally planned to buy a desk converter (eg Varidesk) but thought those very expensive and ugly. I already had a favourite oak desk I wanted to use as the top for this and on the day just removed the legs and existing desk bracing and assembled the Flexispot frame upside down into it. Instructions are very clear with a support email for any broken or missing parts on the box before you open it. All the component Allen bolts and tools are laid out with clear A,B,C referencing and very clear cross referenced instructions guide you through the build. The only thing I added was some cable clips of my own to align the mains cable to the frame top to ensure it stayed clear of the cross member transmission for the motor which raises and lowers the mechanism. Adjustable feet are positioned at each corner to level up for uneven surfaces eg on/off a rug. Also rock solid positioning at any height selected and up to four user-set heights can be programmed and the desk moves automatically to those positions very smoothly and with a nice deceleration as it reaches each position so as not to jolt anything on the surface (eg mug of tea!). Although I have not tested it, it stops if it collides with anything in its path so very safe to use. I am now thinking of getting another one for my wife’s craft space. Would highly recommend this. Someone has posted there is no stop facility. This is wrong - if it meets resistance or auto reverses for a short while and stops. Just try a memory button to raise it and drop something light eg a pen on the surface and it auto reverses automatically. I can confirm this as I tried it a number of times.

I needed a sit stand desk frame that could fit into a confined space in my bedroom. I am really happy with this product so far. Due to the space limitation I had to get a custom cut to size table top made of birch plywood to go with it. If you don't have space issue any standard table top will work just as fine. What I like about the product. Speedy delivery. It arrived much quicker than what was indicated on Amazon page. Arrived at least 10 days earlier than expected delivery date. Quality materials, sturdy frame and good quality paint and finish. I opted for white, good quality fixture and easy to assemble. Adjustable width for small spaces. Although Single motor I think there is enough power. The controls seems to work seamlessly without any lags. Comes with some cable management clips to avoid the adaptor and motor cables hanging at the bottom side of the table top.

The good: It’s surprisingly sturdy, for the money I was expecting it to be more wobbly and was planning to add a truss/cross-brace to remedy this but it’s not needed. On carpet it’s more wobbly as you’d expect than a hard floor. It’s quiet and I’m not seeing any need for the two motor increased speed/load capacity offered by more expensive models. Not so good: As noted by others, the beam that joins the legs is too low to fasten to the top without spacers, you’ll need about 3mm of something, I used M8 thick washers, bit of a design failure there. A number of places use screw heads over slots to fasten parts, meaning the screws would gouge into the metal when tightened, so I’ve added some washers, for 20p of parts the assembly would be much better. The suggested cable routing and power supply holder takes a nice clean look and makes it messy, get an under desk cable tray and route the cables to that along with your others for a much better look. The screws to attach the desktop mess up the rubber bumpers, again some washers sort this. So really good for the money, a little more attention to detail and it’d be so much better.

I added the standing desk frame to an exiting old tabletop. I did need to bolster the tabletop I used as it is wider than the max specified for these legs and I wanted to strengthen where the legs screw in. Most people wont have that issue. Assembly was easy and I did it single handed. Safer would be 2 folks to flip it back up once everything was attached but it really was simple. The height adjusts quite quickly, the height controller is easy to use and the whole thing feels really well made. Give the price of some of the alternatives out there, this is a genuine bargain as far as I'm concerned. I'm 191cm tall (6'3" in the old money) and I have the desk just about all the way to the top (probably about another 3-4cms available. At that height there is a tiny bit of wobble when I type. It is not off putting at all and I type a bit harder than most so maybe you wouldn't see it at all. In summary this is probably one of the best value items I've ever bought online. I thoroughly recommend it. ps. apols for the state of my spare room! ;-)

Fantastic product. Very sturdy, great and easy instructions, especially like the pouches of bits that were given independent letters to make assembly even easier. I have bought two of these now as I was so happy with the first one. If you are thinking of getting an electric frame, I cannot recommend enough. I had a small query regarding delivery and couldn't have got a better service. Great product, great price and great service. What more can you ask for. If you are thinking of getting one, look no further.... :) 😀 😃 🙂 🙃

I wanted to buy the three-stage version of this frame but I had to get this one instead because I needed it to fit in a small space. I'm glad now, because this one was cheaper and it does everything I need it to. It's rock-solid in a low position and there is only a slight wobble when it's at standing height (111cm for me). The presets make it effortless to use and the motor is smooth and surprisingly quiet. Assembly was really easy thanks to clear instructions and clearly labelled parts. I made my own top from plywood because I needed a bespoke size but the frame came with all the fixings I needed, so I just screwed it on. As long as a slight wobble at the higher settings doesn't bother you, I can't recommend this desk highly enough.

Very good quality. The price point is excellent as well. I was hesitating purchasing a manual rising desk as I was not too sure about the quality of the electronic. Eventually I went for this, and I am very impressed. The action of the motor is smooth and relatively quiet (not whisper quiet, but just a nice whirr). The motor goes from top to full speed in a progressive way, which means it doesn’t feel bumpy. Same for reaching the target height and slowing down. Very sturdy and stable even when raised to 110cm. It feels very well made. The instructions are very detailed. Some more tricky part, but well identified in the instructions. Very happy with the purchase.