Lepro Warm White LED Strip Lights 5M (No Plug, Striplight Only), 300 LEDs, 2300lm, 3000K, Stick on LED Lights for Kitchen Cabinet, Counter and Cupboard (DC 12V Power Supply Required), 2 Packs

Brilliant and bright

Good bright lights. Using above and below kitchen wall units. Gives a lovely accent light. Already had transformers, so these were ideal

My study doesn't get sunlight until the afternoon so can feel cold in the morning, so I wanted something to lift the room. I put a strip of lights around the desk back and sides. I think it does the desired effect without needing too much lighting. I also think it looks pretty cool. I purchased a set of 8mm connectors for these LEDMO Kit 8mm connectors LED strip light for white / warm white LED strip lights type 2835/3528 and made a T shape of lights, a small stubby bit that connected to the transformer near the corner, one length then went down one side and the other longer bit went along the back and other side. Biggest issue was that I stripped the sticky cover off and it kept sticking to everything. I should have had confidence in my measurements, and cut it and peeled as I stuck; worst case I would have had to cut off and throw away a few LEDs! I connected the transformer to an adapter which I can control through my SmartThings hub and Alexa too! ;)

Well I'm hoping it stay 5*. I have attached it inside my horse trailer. Work super . Just hope sticky stuff works ok. Will know over time. But tbf they are great and easy fix. I cut the ends and just attached to wire. Then stuck and cut off tape. Super easy.

Great LED strip with Good adhesion, bright white LEDs and close enough together to make a bright continuous line. Used as an uplighter from a pelmet in a hall and look superb. Easy to cut and solder wires on to the PC track for additional length. Hopefully good life but only time will tell!

Easy to use and gives a lovely light above our kitchen units. Simply cut to length at the marked positions, about every 50mm and stick where you want them.

Highly disappointed with this purchase. It's literally just the reel of light strip and nothing else. Since there is no power plug included in the package, I couldn't use it and chose to return it rather than spending more money to buy a separate adapter. Make sure you read the fine print before buying

Good lights

Een goede service

I cut these into 3 13.5" strips per tank, and they light the tanks up great! very easy to install, the adhesive backing is quite good compared to other lights ive used. they are stuck to eggcrate diffuser and were very hard to unstick if i misaligned it. Highly recommend! I even have about 3ft left over for something else i might need to illuminate. Its going to take a while to see if they are strong enough to grow the plants in my aquariums, but i have a good feeling about them.

Lyser som den ska

Tack, jag är nöjd…

So far so good! I've purchased a couple of these to light up my shed and I have to say, pretty darn cool! No really, not hot to the touch at all!! Sorry. I cut each strip into three separate sections, used their tape backs to attach to the rafters and then wired them up to small solar station. I thought that just using the first strip was bright but when I added the second, WOW! It also helps that we painted the inside of the shed white and very light blue. Even though they come with strips of tape on their back (and which I gladly used) I also used some clear mono-filament and some small brads to zig-zag them to the rafters due to the constant hot and cold fluctuations. I've had the first set up for a while and, knock on wood, they've been working great. Easy to work with, very bright (even though I didn't go with the 5050 strips - larger LEDs further spaced) and they don't draw a lot of power. I opted for the "Daylight" LEDs because I wanted the most bang for the buck as it were. Not disappointed. I feel the warmer whites, in this particular implementation, would have looked "off" in a shed. My humble opinion, your mileage may vary. I would absolutely recommend these to anyone who is interested in a low voltage or solar lighting project. Edit: The picture shows a single LED strip (5m) that I cut into thirds. This is prior to installing the second strip. No other lighting and no special photo effects to make things look "brighter". That one strip put out a heck of a lot of light all on its own.