ARGB Strip,550mm RGB LED Light Strip, 3Pin 5V PC Computer Cases Controller Lighting Strip (1 Set led Light)

If you would like to add some RGB lighting to your case then this is the light for you. It plugs directly into the header on the motherboard and syncs using your motherboards RGB program, it's ARGB 4 pin plug do not try and plug this into a RGB header (3 pin) as it will not work and will damage your board. ARGB IS BETTER THAN RGB the effects of the lighting are way better too.This strip looks awesome, it can bent to fit round your motherboard or round more or less anything inside your pc and the lighting that comes from it is amazing.

Now this is a lovely lighting strip, it's actually a Phanteks strip but that's not mentioned in the listing. All the LED's are addressable if your motherboard or lighting controller supports that (MSI mystic light definitely does). The lights are nicely defused through the cover, which adds a much calmer ambient colour to the build. Only gripe is that the included 3M double sided pads are useless, they can't hold on at all. I've switched to a different 3m tape but even that struggles. Vertically maybe it's not so bad but be aware if you're mounting to the top like I did. Would definitely recommend this strip though, it really is very flexible!

What can i say i bought those awhile back and look really nice in my case, finally i have light inside so i can see inside my case.The leds are the best light strips I've seen until now. Looks amazing and easy to install too.However the adhesive its not that good as one clip refused to stick any longer and when i cleaned my pc i had to remove it and use ony 3 for my right LED strip. If it comes to that i will boy another adhesive just to keep everything in placeI want to say that i bought the product from overclockers in the end.This product its shipped from Tianjin China and i waited 2 weeks just to have it lost at customs in UK. :(But i bought them at 16£ and the next day those were 11£ so the guys were good enough to give me the discount of 5£ so there's that.One more thing, to control the lighting i use the software that controls the RGB on my motherboard

The media could not be loaded. I was a little apprehensive of buying an LED strip kit just due to the number of products available to buy. I chose this one over others due to it's built in diffusion of the light and I'm glad I did.The kit arrived complete with plastic running attachments which not only stick to the back of the case with the supplied 3M sticky pads, but they also have holes pre-drilled to be able to screw in behind the motherboard to the case fixing points.Once the clips were ran where I wanted, running the strip was straight forward. There is enough flexibility in the strip to navigate through and around existing wiring within the case without having to remove or detach anything. The 600mm wiring extension is more than ample to allow cable management without stressing the wires.The strip itself covers two full sides of my microATX motherboard and has a short left over length tucked in at the bottom which, when looking at it, is where the GPU covers anyway so you cannot tell it only goes so far across.There are expansion ports on both ends of the wiring adapter to allow more strips to be added.The strip runs on a 5v 3 pin plug, which needs connecting to some form of USB controller. It is not a 12v 4 pin plug which is what is required to run from my motherboard. I already had a pre-existing LED Controller so I was able to just plug and play.The LED strip works really well with ASUS Aura Sync and runs well with the case and GPU fan I already have which are both synced through the same software.Overall very impressed and I will buy another strip once I've decided where I want to put it. After all, you can never have too much RGB!

The LEDs themselves were very bright, and impressive. Although, there were a few scratches on the diffuser itself, out of the box. I wasn’t too fussed over it, but it did bug me.I had this delivered 15 Dec and I believe the LEDs stopped working around the 22nd.Now it’s not devastating, but it is disappointing, coming from a brand like Phanteks.I’m willing to return the item but I would like to hear from the supplier to secure the exchange.

The media could not be loaded. A nice edition to any rgb set up. Works with aura sync and works well with a 3 pin controller.Colours are nice and bright and it was very easy to install.Highly recommend this product.

Looks amazing, I've not set up the lights full but plugged them and they look great

Bought this for my ASUS b450 f strix motherboard as on product it says compatible with AURA sync. But unfortunately this product have only 3 pin 5V connector while my motherboard use 4pin 12V.Product look great and one of the most beautiful RGB leg strips.Edit: seller did put correct instructions and what is supported but i did not pay attention.