Canpump CF 3030 G Pressure Washer Pump | 3000 PSI, 3.1 GPM, 3/4 Inch Shaft, Horizontal, Triplex | Fully Serviceable with External Unloader Valve | Commercial Grade Replacement Power Washer Pump

The pump was an exact replacement for my old one. The installation was fast and simple and the pump came with oil. Works great with a lot of pressure. Cleaned my deck and concrete quickly.

I have an old Honda gx -200 the chemical valve broke the other day and I tried everything to fix it. Anyway, I decided to just buy this brand new pump. It arrived today. It came with oil inside the pump. Which was excellent. It fit perfectly. You will need the 4 bolts your old pump has and also the key. There was not a key in the kit or the 4 bolts. Which is fine but just an fyi. Be sure to not loose the key (metal bar)in your old pump when you take the old pump out to replace it. It’s literally just a little rectangle metal bar. The key will fall on the ground. It took a minute to line the key up with the pump. I just lightly pulled the started cord to move the pump shaft around. Took maybe 15 min to put the new pump on. One seal was loose in the package so it took me a little while to figure out where it went. The directions were great. I checked the oil. Came with 50’percent oil in the pump. Started it up with the water hose and gun attached and it felt like it had about 100x more power then the old pump. I used it for about 20 min and it worked amazingly well. So far so good. I will up date the review after a few more uses but so far five stars. Update. Used the pump today on a fence and then a concrete wall. Ran for maybe 2-3 hrs straight. Works great!! It’s like having a new pressure washer!

The pump it's very good product, fit fine on honda power washer.

I purchased this pump for my Dewalt DXPW3025 3000 PSI pressure washer after the stock AAA 8.7Ga12 pump blew out for no apparent reason. The pressure washer uses a Honda GX160 engine, which is on the lighter side of the engines mentioned here in the reviews.As you can see, the CAN Pump is a perfect fit. Installation is a breeze, it literally is four bolts holding it in to the keyway, so you merely rotate the input shaft to match the keyway and the pump will bolt right on.Don't forget to add oil! This pump doesn't come with any. I purchased the Amazon Mi TM AW-4085-0016 "power washer pump oil". A bit pricey for the bottle size and it is just short of the right amount. Similar oil is available at a particular "orange" store near you if needed.Note that the sight glass (pictured) will read just shy of half full if you pour in the entire bottle. When the washer is in use, the oil level drops to almost nothing in the sight glass! At first I thought the oil was gone, but when the pump was shut down the sight glass level gradually returned to the halfway mark.The pressure is what my old 3000 PSI pump used to do - this one is the same PSI but 3.1gpm rather than 3.0 but I didn't really notice a difference. The Honda drives it without struggling and it performs well. Time will tell how long it will run, but I am hoping with proper maintenance and "pump protector" fluid between uses I can get as much or more usage out of this beast.Overall I am pleased with my purchase and it was a lot cheaper than dropping $700 or so on a new pressure washer.DECEMBER 1 2021 UPDATEThis pump is still going strong! I remain very happy and do recommend it.

So my O.E.M.Technoligies pump which had around 40 Hrs. on it (& was working fine) started to have a slight oil seepage at the bottom I figured Hmmm time to replace it. They are good for around a Hundred Hrs. so I plan on selling it for $40-5. The new pump had to be relocated because it didn't clear the handle. No big deal it took about an Hr,& was EZ. Right off the increase from 2.3 GPM was noticeable. I set the downloader to 2400 PSI & which seems perfect. It looks well made & works flawlessly. We'll see how durable it is.

Bought a customer return at TSC Simpson with a CRX 224cc motor for $100 note said no pressure; Well they were right the axial cam pump had the keyway spun right out of it. No problem though I had really just wanted the frame to mount a Predator 212cc/qualtiy pump and do a couple mods including electric start. Small issue is the soap injection is doa going to reach out to seller for support but we use a foam cannon most of the time anyway so not a big deal.The Simpson pump had Allen key bolts that would not work on this due to wrench clearance. The required bolts (on most engines) are 5/16-24 x 1" Grade 5 w/ real lock washers (Not Split Rings!)Tl;dr got the pump on and it runs beautifully the CRX motor starts first pull, runs right around 3k psi, I set my unloader to spike @ 3100psi and it runs a 16" surface cleaner as good as anything else.

The New Pressure Washer Pump Saved the day! was thinking about going outand buying a new pressure washer, yet for the money it makes more sense to justreplace the pump and add it on to the existing Honda Motor I already had, I'm VeryHappy with the result!

Looks quality and appears to fit my application.Was disappointed to see what was listed as a Italian pump,sold by a Canadian company,from a distributor in Pennsylvania, of a pump clearly made in CHINA.Does come with extra o rings, and appears complete.Price does make it attractive option.