Protector Case Compatible with Lenovo Legion Go 8.8" 2023 Handhled Console,Legion Go Accessories Soft TPU Cover Case with Ergonomic Grip,Anti-Scratch(Black)

This protector case is a perfect fit for the legion go and helps round out the corners of the controllers to prevent them from digging into your hands after prolonged use. The sleeve also helps improve the grip on the controllers. However the one problem I have with this protector sleeve is that when you have the sleeve on, it makes it to where the legion go won't fit properly into the Butterfox carrying case. You have to force the legion go into the Butterbox carrying case to get it to close, but does fit in the carrying case that the legion go comes with. Other than that, its a great sleeve for prolonged game sessions and protecting the legion go.

The case fits nice and snug on my Go. I have no issues with the shoulder buttons with this case on. It feels nice in your hand and improves the feel of the device immensely. The only downside is that with it installed, it will not fit into the case that you got with your Go. You can maybe really mash it in there but I would advise against it. All in all a great case though.

I love the case it gives it a little more comfort/ better ergonomics. I use a 90° USBC female to male adapter so I had to cut a little bit of the case to get it to fit but other than that it is as described and fits perfectly no problems at all

Had to cut out RB M1 buttons because they basically the same button and it was very hard to use.

The LGO doesn't dig into my palms or slide around the table anymore! It's easier to hold without accidentally hitting buttons and I always feel like I grabbed a gadget out the freakin Batmobile. It is built so precisely the vent holes line up perfectly. The few small issues it has only became apparent with extended use and after reading others bash it online. It's not anywhere near as bad as they make it seem though. It does make RB click weird, and the bottom piece is flappy. Just needs a couple of tweaks but otherwise it is awesome and definitely a keeper. It also fits inside the LGO case but you should avoid that if you use it regularly. I don't anymore because the shell and a screen protector are enough for use around the house. Tweaks: RB feels mushy, is always pushed in or sometimes doesn't click. There's a tab on the inside of this shell that separates M1 and M2 that's doing this. Confirmed this was the problem by holding my fingernail between those two buttons without the shell on. It doesn't let RB rock properly and gets worse the harder you grip. I clipped down the tab with some angled clippers and it improved RB dramatically. Now RB clicks right and is not mushy. They should fix this but I'm keeping it so I just clipped it down about halfway taking off something like 1 to 1.5mm. This next thing will only bother you if you have OCD. The shell feels a little loose on the top/bottom but a bit of paper less than 1mm thick fixes that. A few pieces of a business card taped to the inside of the bottom make it really snug. Also, I applied double sided tape to the middle of the bottom piece to keep it from flapping. Used non-permanent 3M 300LSE tape (not included) so it comes off easily. Some silicone Steam Deck and phone shells use similar tape. Using it with the original LGO case: Can it fit in the original Legion Go case? If you really want it to, sure. I'd take a trip with it, not commute daily. The seams of the case may not last as long with prolonged use and there's also a risk of cracking the controller connections if you apply pressure unevenly pushing it into the case. Don't do it if your controllers came wobbly! That's just asking for trouble. Would you leave this shell on the LGO for storage in the case, and what about charging it in there? Nope not for long term storage. It is too snug. You'll need a different case if you need to regularly use one and want to store the LGO with this shell on. Absolutely NO to the second question. If you push the LGO in far enough into the case to attach the charger, you've broken something lol To get it to fit inside the LGO case, start the top part (triggers side) then gently push down on the bottom half of the LGO with both hands thus applying pressure evenly across the device. The attached controllers are a weakpoint that should not be stressed so avoid pushing only one side or at a single point. You'll hear the rubber creak against the case as the bottom half slides in. The lid doesn't shut freely anymore, as shown in the picture, and it never will. Resting one hand on it (no force) closes the lid enough to zip the case shut. It does fit in the LGO case in a pinch if you're careful about it but you won't want to for regular use or extended periods. Get another case if you don't want to take this shell off every single time.

Perfect fit

This makes the legion go much easier to hold while playing and prevents you from touching the hot areas on it. What I don’t like Does not fit in the original case while installed The material above the controllers on the left and right hand make it hard to install and simply get in the way. I cut them off. If you search Amazon there is a version of this case that has it already removed. I do use it but wish it were a little bit better.

The fitment and quality is actually pretty good as well as the texture ans firmness of the case.

Does what it says on the tin, feels comfortable in the hands

Buen producto

Le quedo a la perfección a mi lenovo legion go. Aunque la consola con ella se calienta un poco más pero le sirve de mucho para evitar cualquier raspón o arañaso a la consola.

Un producto a la medida, de buena excelente calidad, lo recomiendo 10-10!