Sovol3D Printer PLA Filament 2kg (4.4 lbs) Spool Printing Materials, Wiring Tightness, Dimensional Accuracy +/- 0.03 mm, 1.75 mm, Black 2 Rolls

The unit works very well, it has a timer from 1hr to 12hr, but can’t be set to be on longer than that, for longer time, you need to extend the countdown timer.It has a small fan at the bottom which helps to remove the excess moist from inside the box, thermostat can only be set to 4,45 and 50 degrees, it has a humidifier sensor that gives you real humidity inside the box. For rhe price, it has an excellent built and functions.I recommend.

I'm a relative novice when it comes to 3D printing, but I found this filament so easy to work with on my entry-level Anycubic Kobra 2 Neo.I sliced a print-in-place jointed Leaf Dragon in PrusaSlicer and, as a challenge to see just how far the print speed could be pushed with this filament, I set the extruder to 210°C and the bed to 60°C and went for the full 250 mm/s. Much to my amazement and pleasure, it printed out absolutely perfectly.No tangles. No snapping. No stringing. The whole 4 hour print job went without a hitch and the colours were stunning!Sovol will be my go-to supplier for fancy multicolour filament from now on for sure.Highly recommended.

Comes very well packaged looks good.It's air tight with the lid down and when drying it's stated the lid should be open on it's built in stand offs which double as closures.The controls are touch sensitive, a little over sensitive, you can set 40, 45 and 50C and the timer from 6 to 48 hours, not 6 to 12. You can see temp and relative humidity altho absolute humidity would be more useful.The base gets warm in use and the fan can't be heard in the day.If you're going to use the box to feed a printer, get 6mm threaded pneumatic connectors for 4mm teflon tube and swap out the existing ones, the nut can be reused.Also this will work way better(like all heater type driers if you out silica gel in there, propping the lid and letting the air circulate outside is a little hit and miss.I'd shut the lid and put silica in there to soak up the released moisture from the filament.Oh mine cost 40GBP it's now 60.

You can’t go wrong using Sovol filament in a Sovol printer, it’s good quality and prints great

Truth is; I didn't expect too much... I thought it might be just enough to keep filament dry, rather than to actively dry "wet" filament and worst case it might be almost acceptable as a reel holder for filament in use. As it turns out it is exceptionally good as a reel holder, it dries filament well, it preheats filament while printing aiding fluidity, it's just... Good... It has a relatively small footprint on the bench, which is really nice... I'm happy, I'd buy another and I am pretty confident that you'll have results like those that I have had... Give it a go...

Seems like the heater struggels to reach the temperature setting. The dryer need som additional holes so that moist air can evacuate the drying chamber.Othervise it works as intended.

My first dryer from Sovol needed a new fan, it was noisy. They replaced it without a quibble. That dryer last exactly two years. It did a fantastic job of drying filament so I bought another. I found out that the old dryer was fixable, it just needed a new heater element. Fully expecting to pay for a replacement Sovol sent out a replacement part free of charge, one year after the guarantee ran out. I will always buy from Sovol including its filament because when you find a good customer-oriented company you would be silly to stop. As for the running of the dryer. It has three set temperatures. 40c/45c/50c. When drying filament you don't want it to dry too fast as the outside of the reel will be dry but the inside might still be damp. So, I recommend the slow burn. It has a timer which runs incrementally from 6 hours to 12. After the timer stops the dryer switches off. However, yes there is a however. The aforementioned heater element will probably last longer if you keep the dryer's feet off the table. There is a stand that fits the sovol on Thingiverse that does the job of providing good underside ventilation. I highly recommend the Sovol SH01 Filament Dehydrator Spool Holder.

First things first, the item arrived very well packaged with foam padding both inside and outside of the dryer for excellent protection.The setup was very easy to understand and use, basically just plug it in, pop in some filament and set the drying temperature and time on the front panel and let it do its thing.The nice touch is that you can see the moisture content within the drying chamber throughout the process and I can confirm that it does bring down the humidity levels quite a bit, however even though the chamber is fitted with a seal and locks the humidity does seem to rise again quickly once the drying process ends. There are rubber bungs to close any gaps from the filament feed holes and even to block the power socket, but somehow the humidity still rises fairly quickly.Does it do the job? Well yes it has helped with drying out some older filaments, but I find keeping the dryer running whilst printing provides the best results for me. I’ve given the 4 stars purely for the fairly rapid return of moisture in the dryer even though it’s sealed, but if you can live with that it does a good enough job.

I've been told over the years that I needed to buy a filament dryer but I've resisted due to cost and only being able to dry one spot at a time but now that I've gotten this one I wish I would have gotten one earlier . In the pictures you can see a before and after . The filament I used was some of the oldest filament that I own so I wanted to see how well it would revive it and wow was I surprised after just 8 hours @ 50c in the dryer the filament wasn't brittle anymore.ProsAble to dry a variety of materialsCan dry up to 2 spools at one timeCan print directly from the machine.Bright and easy to read, use and understand touchscreenConsI wish it came with desiccant to replace in the dryer.I wish the fan was a bit quieter.I wish the rollers to feed the filament while printing from the box were a bit more smooth .

A secadora em si é muito boa, bem construída e funciona perfeitamente. Porém, como ela só chega no máximo a 50°C, só é possível para usá-la para secar PLA, então tenha isso em mente quando antes de comprá-la.

As someone deeply immersed in the world of creative design and 3D printing, achieving optimal filament quality is paramount to my craft. Enter the Sovol Filament Dryer – a game-changer in ensuring consistently flawless prints and elevating the precision of my creations to new heights.**Enhanced Filament Quality:**The Sovol Filament Dryer's advanced technology excels in maintaining the perfect moisture levels in my filament spools, ensuring they remain dry and free from any moisture-induced imperfections. Whether I'm working with PLA, PETG, TPU, or ABS materials, this innovative device consistently delivers top-notch filament quality, resulting in smoother prints with impeccable detail.**Customizable Drying Settings:**One of the standout features of the Sovol Filament Dryer is its customizable drying settings, allowing me to tailor the drying process to suit the specific requirements of each filament type. With adjustable temperature and time settings, I have full control over the drying parameters, ensuring optimal performance and minimizing the risk of print failures due to moisture-related issues.**Universal Compatibility:**Versatility is key in my line of work, and the Sovol Filament Dryer delivers on all fronts. Compatible with both 1.75mm and 2.85mm filament sizes, it accommodates a wide range of filament spools, offering unparalleled flexibility and convenience. Whether I'm experimenting with different materials or working on large-scale projects, this dryer has me covered.**Effortless Operation:**Operating the Sovol Filament Dryer is a breeze, thanks to its user-friendly interface and intuitive controls. With just a few simple steps, I can initiate the drying process and have my filament ready for printing in no time. Its compact design and spool holder functionality make it a seamless addition to my 3D printing setup, maximizing efficiency without taking up valuable workspace.**Reliable Performance:**Reliability is non-negotiable when it comes to my creative endeavors, and the Sovol Filament Dryer consistently delivers. From its robust construction to its precise temperature control, this device instills confidence with every use, allowing me to focus on bringing my designs to life without worrying about filament quality issues.**Final Verdict:**In conclusion, the Sovol Filament Dryer is a must-have tool for any serious 3D printing enthusiast or professional. Its ability to maintain optimal filament quality, customizable drying settings, universal compatibility, effortless operation, and reliable performance make it an indispensable asset in my creative arsenal. Whether you're a jewelry designer, 3D artist, or passionate hobbyist, investing in the Sovol Filament Dryer is sure to elevate your printing experience and bring your visions to fruition with unparalleled precision and quality.

Es una buena herramienta para mantener tus impresions con la mejor calidad possible. Por el mismo precio te puedes comprar un de una marca mas reconocida como SUNLU per a diferencia de esos es que este seca dos rollos al mismo tiempo y aparte tiene sello y ventilador para un secado uniforme. Altamente recomendable si impremes mucho con PETG o ABS, filamentos que aborben mucha humedad.

Dois rolos de filamento, cor preta e branca. Aproximadamente 2.3kg, somando os dois rolos.