Potauto Universal Nylon PA6 Grooved Magnetic Jack Pad Jacking Puck Pinch Weld (Slot Width 0.55 Inch) Frame Rail Adapter (Qty 1, Black)

Lifting a car should never be taken lightly as people have lost their lives by underestimating the importance of the right equipment for the job. That being said, this puck works perfectly for a 2013 BMW M3 E92 as it has the right height for supporting the weight of the car from where it should be supported. I had to return other brands as they were short and would not reach the top of the car's support lifting platforms. The shorter ones lift from the walls of the support lifting platforms, and in a good scenario they damage the lifting platforms, in a bad scenario they can cause an accident. Last, a huge plus of the red Potauto is that it is very easy to center on the rubber pad of my floor jack, because of the visual contrast between red (Potauto) and black (jack's rubber pad).

I got a few similar ones from Amazon but this was the best - first off it is metal, check all other people complaining about rubber breaking under jack - umm no thanks. This piece fit right in the opening of my 2020 GLC43 (for factory jack stand). It does go higher a bit but it does not impact anything because it rests on the top of the jack pad, not sides. Factory jack works the same way - check pics. Super sturdy, just replaced rear brake pads myself.

This is what you need for the latest BMWs (X4 40i).Perfect fit and sturdy. The engaging height is 15mm as it should be. 12mm is not enough.

This product works really well for Audi and VW cars to ensure you’re using the pinch weld jacking points correctly. My only gripes are that it’s not a bigger diameter or magnetic on the bottom to keep it in place on the jack itself which can still move under the weight of the car. Obviously still use stands but it this product was helpful in swapping out the summer wheels this past weekend for winter tires on my 14 S4 and the wife’s 21 Tiguan

All of my BMW vehicles were purchased as pre-owned vehicles. Every time I buy a "new to me" used BMW I am never surprised when I lift it off the ground for the first time and discovered that the jack pads have been completely destroyed by either the previous owner, or, more likely, the people that have done maintenance on the vehicle on behalf of the previous owner. People who are new to the brand simply don't know how to properly utilize the jack pads that are fitted to every BMW vehicle. The jack pads are made out of hard plastic that is fragile if used incorrectly, but incredibly strong and provide extra stability when used properly. You must use a jack pad adapter of some type in order to utilize them correctly. Most people, however, simply don't want to spend any extra money to use them properly, or don't know what they are, so the jack pads get destroyed over time. Then the vehicle gets sold to someone like me who ends up having to replace all of the broken jack pads. It's my lot in life.What makes these Potauto Universal Aluminum Jack Pad Adapters SO useful is that they are very well made, they are durable because they are metal, you can get them in bright red, and they are very reasonably priced. Why does it matter to me that they are red, you ask? Well, I once drove around for two weeks with a black jack pad adapter made by a different manufacturer stuck up inside one of my destroyed jack pads without even know it. Once I had lowered the car, the adapter didn't drop out of the destroyed jack pad. It was dark, the jack pad adapter was black, I was tired, and I didn't notice that it was stuck up in the damaged jack pad. Can you imagine a metal jack pad adapter coming off at 75 mph on the highway! Luckily that didn't happen, and I'm surprised that it didn't. All of my jack pad adapters are now red, and I never leave one behind.Therefore, these Potauto Universal Aluminum Jack Pad Adapters in red are a must have if you work on your own BMW. Utilize them properly and keep your jack pads in factory condition.

This is a review for the Mercedes pad made to fit the indention on the jackpoints on the sides of the car. The 2000's and newer MB have these weird rubber pad things on the jackpoints instead of a typical pinch point or even just a flat surface, which make it difficult to use a standard jackstand. I'm happy to say that these aluminum pads are a near perfect fit and allow use with both a jack and/or jackstand.I did consider the rubber versions of these pads, but read too many reviews about how the rubber ones deform, and didn't want to deal with that, so went with the aluminum pads.When I test fitted these pads before use, I was a bit concerned since they are not a flush fit in that the middle portion is about 1/4 inch too long, which means that the car rests on just the middle raised portion. I wasn't sure quite what to expect with this kind of weight distribution, so I jacked up my car by the center jackpoint, and then lowered them onto the jackstands with these jack pads in place, half expecting the car to slide off of these slick looking aluminum pads. However, once the weight of the car was on them, there was absolutely no movement at all. I did the usual shove test to make sure that the car wasn't going to go out of balance and was going to slip off the jackstands and fall on me and crush me while I was working on it, but it was as solid as can be.Quite happy with how these aluminum pads performed, and also happy to see that there was no deformation in the metal and no signs of scratches or indention or any defects after the first use.

Lost my aluminum one when I forgot to take it off the pinch weld.This one was less expensive, but he nylon/plastic material is noticeably wearing. Time will tell.

They work and fit my S550 just fine. But while waiting for it I took a master lock knock off and cut the loops off of them and they actually fit perfectly. So if you need them now just buy two master locks or cheap ones the same size and cut the locking part off and they fit perfectly

They fit fine although the magnets did not hold the pucks up. Not sure if the magnets are too weak or non metallic on the car location. I just had to line them up with the jack.Overall pleased with the value of this purchase.

Très bien

Buena calidad, cumple con su propósito, pero no fué lo que yo necesitaba.

An excellent price for a quality product!

I've been looking for jacking pucks for my C6 for a while and liked the idea of an installed jack pad over a puck. I like the red colour because they match the car but are also easy to see so if I'm ever stuck at the mercy of a random shop, it shoudl be fairly obvious where to jack the car. These were really easy to install with 2 hex head screws per pad and even came with an alan wrench.