Comgrow 3D Printer Filament Dryer Box SH01, 3D Filament Storage, Keeps Filaments Dry During 3D Printing, Compatible with 1.75mm/2.85mm PLA PETG ABS Material, Filament Dryer, Spool Holder

this is great works well dries my filament out and reduced my stringing .

As required good pla

I purchased this mainly as a drying box, It does the job and the controls are pretty straight forward. It would have been nice had there been a sealing gasket where the lid meets the base as this would provide a much more efficient seal. It performs the task required of it and enables me to prep the filament prior to printing. It's pretty basic but suitable for the demands of most filament. I have an AMS 2 which can also dry the filament but only when no filament is loaded into the gear mechanism and not during printing. At this price point you expect products to be a bit plasticy and this unit continues that tradition.

Love this product, I always keep a spool of it as my go to filament for reliability and quality product, never have any problems , adhesion to build plate is excellent ( creality mag bed) i dont use any products to aid adhesion , the quality of the print is great with a nice shiney appearance and colour is uniform, cost is good although a touch more expensive than some filaments I have used ( usually Basicfil) iyts worth it as you know your going to get a good finished product. Thoroughly recommended.

As a beginner to 3D printing the first filament I bought from another company didn't work on my Labists X1 (seems it needed over 200 degrees to extrude)...I was hoping this would be different and it worked straight away! I printed an echo dot holder successfully which I've been using since. I can't compare it to other spools as this is the first one I bought (which works) other a short multi coloured set for 3d pens which wasn't ideal for for prints requiring over 15 meters. What I can say is that it is nicely spooled (not tangling anywhere) and very even throughout.

After leaving a a dissatisfied review on their PLA Comgrow got in touch regarding my review ( didnt expect them to) and after a lot of communication between them and I we came to an amicable agreement. I have now started printing with their PLA even though I was hesitant to do so but I`m now one hour in on a 3hr print and I have to say the product is extruding well and adhearing to the print surface. So two big thumbs up to Comgrow 3D for customer service and discussing the issue with me. Would buy again, but also not that there will be from time to time products that slip through the net I understand this but their customer service more than made up for this. Well done Comgrow 3D

I have used this PLA a few times before in white. I've had a few problems with blocking and uneven prints with the white. The last one I bought was grey. I tried several times to print, but failed every time with poor bed adhesion and lumpy filament laying. The quality is simply awful. It's almost as if there were none melted lumps in the printed lines! I have an Ender printer which I've used for many print jobs without issue. I then bought a role of proper Ender PLA filament and it printed like a dream! Obviously the cause of my print failures was this make of PLA. My advice, spend a bit more and get a quality filament. This product is not fit for purpose.

I’m extremely new to 3d printing and took up the deal to get this pla with my printer, cheap enough for my spaghetti mistakes as well as printing toys off for my daughter to paint

Spule kommt sauber aufgerollt, vakuumiert und mit Silica Gel Beutelchen. Material lässt sich super verarbeiten und ist nicht sehr brüchig. 205 Grad Düsen- und 55 Grad Betttemperatur sorgen bei mir für perfekte Haftung und Verarbeitung. Werde auf jeden Fall noch andere Farben nachbestellen. Weiter so Comgrow.

Um dos melhores PLA para impressão

Top Ware!

Parfait pour moi,bonne adhérence au plateau.

I had problems with this material. I used only the black one and clogged my 2 machines (Ender 3 s1 pro and my older ender 3). One of the machines has not been working since then. I changed the nozzle, however, it is still not working. It was a brand new hotend kit :(