TACHICO 8pcs Motorcycle LED Lights Kits, APP Control RGB Smart Brake IP67 Waterproof Accent Glow Neon with Dual RF Remote Control for Harley Davidson Honda Kawasaki Suzuki

Bought these for motorcycle in April 2022, installed them mid June 2022. As of now August 2022 they don’t work. One day they just shut off and that was that have tested and it is the unit that is dead. Tried to contact sellers to no avail.

I happen to be a fan of LED RGB lights, so when it came to upgrading my son's 50cc Chinese Boom scooter starting with gas, spark, air, the thought of LEDs came naturally. Although irrelevant, I replaced the analog gauge cluster with the Trail Tech Vapor (see pics and review under that product) and added the digital Koso Mini-3 Fuel gauge. So it's time for some LEDs. This kit worked out nicely and easily (please see attached pics).Although not entirely necessary, I ordered the Suzco 4 pc extension kit for $12.20 in case I needed it. Turns out I did need one extension for the right rear. All other kit wires were long enough as is. There really isn't much else to say other than locating the positive brake wire was probably the biggest challenge. I found the brake wire harness in the right rear without much trouble, unhooked it, put a negative volt meter lead on the battery negative and started test probing wires in the harness to identify the brake positive. Using the extension cable provided (which I did use to extend the control box from the ignition tap and frame ground in the front to inside the bike's body), I peeled out the blue wire and zip tied it along the frame to the harness and tapped the identified brake wire. The kit works perfectly turning the bike red whenever the brakes are activated.My kit had the eight LEDs, and this was sufficient for this size bike. The colors are all quite nice, and our favorite setting thus far is "flash" which cycles all the colors one at a time, the rate adjustable by the dimmer buttons on the main remote. As soon as the key is turned on, the lights come on, and we run the kit day or night without really messing with it. As for remotes, I've really only used the main flat remote and haven't downloaded the app because I just haven't had a need to. The flat remote is velcroed to the bike and easily accessible to change a color or pattern at will.I recommend this LED kit as it has done the job nicely so far, was inexpensive and easy to install, and hopefully it will last without failing.

GOOD PRODUCT

-Likes: Ease of install, brightness, ease of use...3aYs to control the.l colors.Concerns: the connections are not- Concerns: connectors are thin and may break with a heavy/aggressive hand, be aware most bikes will need a wire extension kit to reach the lower frame and rear saddle bag area.Overall I’m highly satisfied with product. The two issues I ran into were due to lake of planning. The included cables a bit short to reach the lower frame and saddle bag supports on my road king however a wire extension kit made it fit perfect. The connectors feel cheap it have a very firm connection. In my haste I broke a connector which as easily taken care of with a bit of electron tape. Lastly the commotions do not seem to be water tight, I recommend wrapping each with the electrical tape for peace of mind. Lastly be aware that the Bluetooth module will always be on if tied into constant power. For my touring bike I tied into the front fog light connector not used on road king standards. I did not have to remove the headlamp assembly, but I did remove the fuel tank, seat, saddle bags, and side covers. Sound like a bit much but it took 15 minutes and allowed me to properly hide and secure the wiring. Total install time. Was roughly two and half hrs. Again plane the wiring route and know your length.

The media could not be loaded.  Was easy to install but I used some crazy glue to make sure it held on. Glue may be better if it's not 25 degrees out but I never know now. No app usage at all. Won't even open on due to a bug it says. Came out once to it on so far so know I will have to put it on a switch. No thrilled about that as I shouldn't have to do that. Overall I am pleased in the construction. Seems durable in comparison to some others I have seen. Did not hook up to the brake light either.

Instructions didn’t come with translation to English so set up was a bit sketchy, once we googled everything instillation was great. Product works great.

The installation process is straight forward. I did notice they turn on by themselves and because of this I got a dead battery a couple of times. I asked on here why and it has to do with interference by the frequency it uses and a solution was to add a killswitch wich i completed today. Was a little challenging finding a good switch rocker, wiring and drilling for the switch to look flawless on the bike. I'm happy now knowing it won't be drawing power and killing my battery. Next is comnecting the blue wire to my breaks. Will update this review when done how well it works and post pictures.