R3 Jr. Pocket-Hole Jig System - Portable Kreg Pocket-Hole Jig - Easy Clamping & Adjusting - Includes Positioning Sliders - For Materials 1/2" to 1 1/2" Thick

I have been using Kreg jigs for many years now, and have this item's predecessor. While I could not live without it, a few things always bugged me - and they all got fixed in this version. It was enough that purchasing it was a no-brainer. The biggest improvement is the built-in offset lip with markings for all typical lumber sizes. In the old one I had to actually screw the lip that is used to align to the edge of the board on using two screws - and if I was using 2x material, add a spacer using different size screws - and if I was using anything else I had to measure and line it up manually. Good if I was doing a lot of boards, but a real pain for one or two and worse if I was switching back and forth! With this new model, just press in on the tab and slide the gray guide forward until it snaps into place at the mark for the size board I am using. Second, with the lip in place, the Kreg clamp I was using was trapped in the jig and if I wanted to use it for something else, or just put it away, I had to unscrew the lip. Done away with in the new model, there is a spot sized for the clamp that is proud of the jig. Very easy. Third, this comes in a nice little case that holds everything but the clamp. My other was part of a set of Kreg jigs so when I wanted to throw it into the toolbag to go to a work site, I had to put all the parts in, and some would eventually go missing. Now I can put the case into the toolbag, very handy. Fourth, the jig from the old set that showed where to set the drill stop required me to lift the drill out of it in order to get the stop on, and of course it would sometimes slip when I tightened it so I have to recheck and sometimes adjust. Honestly it was such a pain that I got an extra bit and stop just so I could leave one set for 3/4" material and one for 2x material. In the new model the jig is part of the case AND holds the bit at each end, leaving space for the stop so I can tighten it without moving the bit. Clearly Kreg is listening to their customers and making very handy and sensible improvements while maintaining their high quality. Like I said, buying this one even though the old one still works was a no-brainer. Now I'll just set up the old one for 2x material and leave it.

I've used the Kreg R3 Pocket Hole Jig on many woodworking projects over the years, and I can say that it is an excellent tool for anyone looking to get started with pocket hole joinery. Pocket holes are my favorite method of joinery because they are very strong and easy to hide, and the Kreg R3 makes it easy to create professional-looking joints. One of the best things about this jig is its cost-effectiveness. It is an affordable option for anyone who wants to start building furniture or other woodworking projects using pocket holes. The jig is also very easy to use, even for beginners, and comes with clear instructions that make setup and use a breeze. However, one downside is that the square bit can deform if driven with too much power. This can be a problem if you're using a drill that doesn't have adjustable torque settings. However, with a little bit of practice, it's easy to get a feel for the right amount of pressure to apply. Nevertheless, I've found that the drill bit that comes with the jig stays very sharp over time, which is a huge plus. It's also easy to find replacement bits online or at most hardware stores, so you don't have to worry about running out of bits when you need them most. Overall, I highly recommend the Kreg R3 to anyone who wants to start using pocket hole joinery in their woodworking projects. Its cost-effectiveness, ease of use, and ability to create strong and professional-looking joints make it an excellent investment for any DIY enthusiast or professional woodworker.

Thank you for fast shipping and good product. I will purchase more merchandise in the future.

I purchased the R3 Jr for use on building a hardwood table so I knew I would be putting it to the test from day one. I will say this system clamps things together beautifully. My largest clamps are only 3 foot and having to buy 8 x 48 inch clamps at about 30$ a piece would come to about 240$ just to properly hold my table top together as the glue dried. This effectively saved me about 150$ just in that one instance. Not to mention I was able to immediately raise the table top and move it where I wanted it. The cherry table top is dense and its size 36x72 as listed in the Kreg directions (every 6 inches) requires 11 holes per board which comes to 44 holes. For ease of use I just went to punch them all out in one sitting rather than stopping to glue and screw. On the second board (11 consecutive holes) the bit started to feel snug in the metal sleeve as if heat from the constant friction was causing things to expand and seize up. Naturally to seat the bit properly I spun up the drill a bit and just kept powering through. It wasn't Until I was through that second board (22 holes) that I flipped the jig over and noticed a fracture in the blue plastic that held the metal sleeve in place... which was now about a centimeter or 2 recessed into the jig. I simply switched to the second hole for the rest of the 22 holes and although I experienced the same slight binding of the drill bit I was able to finish without incident. Keep in Mind I was not putting pressure on the drill I was letting it walk itself into the wood as this was my first experience with this Jig so I was being as delicate as possible. Needless to say I am having Amazon replace the jig and I will see how the second jig works for the skirt and legs of the table putting it through the same stress test. *UPDATE* The replacement jig worked perfectly for the next 40 or so holes. Again this jig is what everyone makes it out to be. An amazing tool that makes life much simpler if you never plan to look at the pocketholes.

Kreg products seem a little pricey but I really like this jig with case. It's easy, convenient and works great. With the case, it's compact and easy to carry and bring with in my tool bag

Muy buen producto fácil de usa

useful for DIY projects.

ポケットホール用の治具、中華製もいろいろありますが本家本元ということで購入。 プラスチック製ですが丈夫です。最初ドリルを通すときにプラ部分が削れますがこれで公差を小さくできるようです。 グリップ付きなどいろいろバリエーションがありますが、いちいちクランプで止めるのは面倒ですがコンパクトでDIYでは十分です。ケースも付いています。 専用のビスは高価なのでコーススレッドを使ってます。半ネジではないビスを使う際には4mmのドリルで下穴を開けてます。

Excelente gabarito. Usei várias vezes, em mdf e madeira maciça (dura e macia) e o resultado é sempre bom.

This is my first pocket hole jig so I may not give the best review with no reference. But for me this is great because I just follow the instruction and then everything was like falling into place. I love the experience in using this jig