Diversitech 6207E Evergreen EM ECM,3/4HP,208V

Not intended to replace PSC motors... but can if you know some basic electrical. Here's how: Motor requires 3 power wires: ground, 230V L1, 230V L2. (or 115V, it'll accept that too). Control requires 2 wires from your 24VAC transformer: common (0V) and 24VAC hooked to one of the speed inputs. If you hook your thermostat C wire (common) to the motor C terminal and hook your thermostat G wire (fan) to the motor Speed5 (or any other speed) terminal then the thermostat commands the blower motor on and you're good to go. Does not use the PSC external capacitor - just remove it. Working great. Obviously high build quality. Very nice motor. The direction auto-learning is impressive. The manual it came with is top notch and answered every wiring question I could have.

Why did you pick this product vs others?: Great replacement for my expensive X13 blower motor. Direct replacement, plug and play. Works fine.

I have an ICP system and this thing was plug and play. Now my A/C is blowing better than when I bought my house. Cooled my home much faster than the old motor.

In 2017 the blower motor in my furnace (AC) stopped working. Knowing that I would pay a small fortune if I called an HVAC company, I figured I would look at it my self first. After removing the panel, a couple of screws holding the blower fan in place, and disconnecting the wiring to the motor (after taking pictures!) I had the fan assembly out. There were a few bolts to loosen and the motor was free of the blower fan. I looked up the specs on the motor and this was the compatible replacement. At the time I paid $270. The new motor went back in place and I have had 7 trouble free years of cold AC in Florida. A week ago I noticed that the fan was running all the time even when the thermostat was not calling for cold air. Something seemed to be stuck on. I first tried replacing some relays in the furnace and checked the wiring and all looked good. Since this motor has the control board inside it, someone in another review mentioned that it was possible for a relay on the board to fail while closed. I looked up this motor again and saw that it was $329. That is really not much of an increase in 7 years. So I figured I would order the same motor again. This weekend I swapped the motor out again and my HVAC system is working normally again. It took about 90 minutes to replace the motor and test everything and the only tools I needed were a set of socket wrenches. This motor is very good value and very reliable. I have probably saved myself thousands of dollars replacing it twice myself. Anyone with some basic DIY skills should be able to replace this motor. Just make sure to disconnect the breaker first! :)

No problems, this replaced a Genteq X13 motor on a York AHU, it lasted12 years old. This one Mounted and matched up perfect with belly band frame mount and existing harness plugs. Comes with install directions as well. We're back online now. I bought the 4 year warranty as the lifespan varies by the reviews, but lots of things can affect this as well, I'm on day 2.

My factory motor lasted 8 years then made some horrible noise like a Harley was in the air handler. So I bought one of these motors to replace it and it hooked right up with no issues at all. Swapped it out in like 30 mins. That replacement one lasted around 5 years. Came home one day to find the outside compressor and lines frozen over. Outside fan and compressor would run but the air handler would not. Couldn’t get it to turn even when manually wiring it without using the thermostat. Unplugging everything and kicking the motor would get it to work for a while but eventually it would just not come on anymore. Bought another replacement and it fires right up and works fine. The shafts on these rust like crazy so they are not easy to get out of the squirrel cage without an angle grinder and a hammer. It is not fun at all. The old factory motor in my Carrier had a stainless shaft that didn’t rust at all in the 8 years it ran.

Motor was defective , doesn’t turn at all

Great replacement, perfect fit, super easy to install.