ZEKOO 10FT Double Track Bypass Sliding Barn Door Hardware Kit for 2 Doors, Bypass Barn Door Track Kit, Low Ceiling, Easy Install, Fit 60" Wide Door Panel

The media could not be loaded. I love the end result from the two Zekoo 6.6 ft Bypass door hardware kits that we've now installed in front of 2 closets, in a home with low ceilings. My husband and brother-in-law helped me with the time- and muscle-consuming installation of this sturdy, heavy-duty Zekoo hardware. It took us three full days, not including door staining or trips to the hardware store. None of us had previously installed any sliding doors. I've read other reviews complaining about the instructions, and here are some things that we learned that might make helpful updates to the Zekoo instruction manual:1) The first step in the instructions should talk you through plans for the wall that will support this hardware. This Zekoo hardware is probably strongest when used on walls with a wall stud at the center of what will become the space above the doors, and additional studs on either side of the center at standard 16" intervals. My house is not so well built, with studs only at the ends of the closets. To compensate and insure our wall would support this heavy hardware, we added a 2" x 8" board to the inside surface behind the drywall above the closet. This board was supported by the top of the closet frame, and made the rest of the hole-drilling instructions work out easily. The Zekoo kit does come with drywall molly anchors. Considering the weight of the kit and my solid doors, my team decided not to trust mollies to hold it all up. We also used a 1" x 6" X 80" board, which I finished to match my doors, across the front of the top of the closet. Using this board gives more clearance for wall baseboards, and it also enabled us to make installation measurements and pilot holes on the board, before the board was installed on the wall.2) Where the instructions tell you to draw lines, I would have said "Mark points." Once the hardware is installed, you will be able to see part of any lines you have drawn on your wall, and you may need to paint or stain over your lines. Unnecessary extra work, easily avoided.3) The purpose of the bottom line is explained in the instructions, but the reasons for the top two lines are not. We learned that the other two lines are guides for the two screw holes in each of the brackets that will support the outside rail. These top two lines are also better replaced by marks versus lines, using a square to line them up at the proper vertical distance from the first, or bottom line of holes (see photo). The two rails ideally will run parallel to each other (otherwise, you will need doors of different lengths). Keeping everything square and using the measurements written in the instructions allows the inside and outside rails to line up properly.4) The instructions suggest screwing together the two pieces that make up the bracket, before mounting the bracket on the wall. If you have very little clearance over the open space your doors will cover, you may have to put the brackets together first to be able to tighten the screws. I only had 8 1/2" between the top of my closets and the ceiling, though, and we found it to be much easier to mount the part of the bracket that goes against the wall first, by itself, because it is harder to screw in the wall mount screws than it is to tighten the bracket connection screws. You can then level these bracket pieces and tighten them down. Separately, in a comfortable work space, you can loosely pre-assemble the other halves of the brackets onto what will be the outside rail, lift this whole construction into place, and screw and tighten all connections. The outside half of the bracket needs to fit over the top of the wall half of the bracket, for the rails to be aligned.5) For cutting the slot needed in the bottom of the door, the easiest approach we found was to ignore the instructions to cut out a notch 5/16" wide by 3/4" deep, and to use a circular saw set to approximately half the width of the door. My doors are 1 3/8" thick and our saw was set to cut 11/16" to cut at a depth of about 1/2". After making one cut in the door bottom, flip the same door over and, without changing the saw settings, saw again (see video). This process neatly created a straight track, which was wide enough to work with the small plastic door guides that came with my Zekoo kits. Zekoo measurements aim to have your doors 3/8" off the ground, so the guide does not have to fit completely into the track on the door. My doors slide very smoothly. We also found that the track was needed. The doors slide smoothly, but they also swing easily, without a guide.6) You will probably need to use many washers to make sure that no parts rub together and to make the kit fit your application. We made a number of final adjustments, including using two washers on each bolt through the outside track, to keep the outside track bolt ends from rubbing the inside door bracket when it slides. Also this kit works with a range of door thicknesses. My 1 3/8" doors were on the thinner end, and the door wheel hardware includes bolts with acorn nuts, which can only be tightened so far. I needed 6 washers per bolt to make this hardware work with my doors, or 48 washers per two door closet. I bought a box of washers.7) Finally, there are no extra nuts or bolts with this kit and there is a pile of hardware to manage. We lost much time at one point. trying to find an acorn nut that vanished. Be careful with the hardware!Other than some instruction clarification and maybe some extra washers and nuts, I think this kit is about as good as it can be, without coming completely pre-assembled. Nice job, Zekoo!

This barn door has been such a great addition to our home. The door helped improve our space around the washer and dryer. It is very sturdy. A little hard to assemble but it was worth it in the end.

Good product....well made, I wish that the holes on the spacer peices were drilled to the correct size...I drilled them out to the correct size. Everything came together nicely.

I ordered the 12 ft system for a large patio slider and hung sliding plantation shutters, and this product looks fantastic once installed and the quality is excellent. The install does take some time because there are a lot of anchors, but the product feels solid and secure. I did experience an issue with the wall anchors provided tearing up my drywall and the anchor breaking while trying to place in the wall. I ended up buying different anchors from a home improvement store. I was installing in a CMU block wall with a concrete header, and I believe the anchors provided are better suited for wood frame construction. Other than that, excellent product and highly recommend!

One pic is only of the double bypass door hardware installed in a long hallway, before the doors. The next 2 pics are of a closet door set I already installed using the Zekoo SINGLE bypass door system that I have used in the four bedrooms of my house to replace all the sets of ugly louvered doors. I will be making and hanging the same style doors on this double bypass system. While I don't like all the busyness of the double bypass hardware, this hallway is our primary storage area, and I need to be able to open the doors completely to get in large items such as our massive generator and many litter boxes, and the hardware is super heavy duty. The quality of Zero hardware is excellent, but it is not necessarily a breeze to install. This is kinda challenging diy carpentry, but the hardware is much less expensive than many I've seen. Hubby and I are more than intermediate do-it-yourselfers, but those who have been unhappy with the instructions should contact Zekoo directly with questions. They really want to make their customers happy. Before shipping this last order they communicated with me to ask me specific questions about my install. They shipped out extra parts that I needed for my application. Quick responses to questions--I've never had this level of customer service from any vendor. They even respond on weekends, in the middle of the night. We have installed a 24.5' track and an 8' track across from it in a hallway with four storage closets. Really high quality hardware--I will post pics when finished.

So....first things first, ladies make sure your help, whoever that may be is somewhat handy and doesn't have a short temper. This hardware is very nice and looks great. If you're going for the modern country feel this will do it for you. Really looks nice. The installation was a little much though. My husband said if I mention the words "barn door" again he will divorce me. This is actually the second set I have purchased. Measure, measure and measure again. Think about your trim around your opening. If you have it I suggest taking it down, and rounding corners and covering door opening with sheetrock and paint. Sometimes you have to use washers or shims to get it to the correct width where the carriages pass each other. Also, the other thing is that slab doors, paneled or flat may not work because of the length. So after that wouldn't work he had to build the doors to fit, that was a cussing fit but it worked and they are beautiful now.

Bang for the buck, easy install, works as it should. Recommend this brand. Company reached out to me and informed me of defective parts, sent new parts to me quickly. Much thanks!