90055 SIZING DIE KIT .452

This is a great, economical way to size your lubed .45 cal (ACP/LC) bullets, and was designed to work with Lee Precision 1 Bottle Liquid Alox (that is no longer packed with the sizing die.,) You don't need very much, and a small bottle goes a long way. The ram works with many brands of presses and the operation is simple, quick, and easy. If you still need help, there are lots of YouTube videos that show how to use it. It works on any lead bullet (to include those with gas checks,) but always make sure they are lubed before sizing. This is a super way to start sizing your bullets if you are new to casting, or even if you've been doing it a while like me.

Lee sizer works great

I have 4 of these in different calibers. I like the ease of use and uniform results.

This is a sizer, not lube/sizer. Use this if you are powder coating bullets, and expect the powder coat to act as the bullet's lubricant. Or if you plan on lubing your bullets some other way. DO NOT RUN BULLETS THROUGH THE SIZER DRY....... THEY WILL STICK & AND YOU WILL HAVE A HECK OF A MESS. When powder coating...... after coating and baking, use lanolin oil and isoprop alcohol in a 20/80 mix. Coat bullets. Take an old press, turn it UPSIDE DOWN, mount under the table, adjust the handles. (Doesn't make sense????) You're used to having the die on top of the press, NOW it's underneath, and you will feed the bullets nose first into the die, and the ram will be going DOWN, instead of up!!!! The bullets will be dropping onto the floor. To catch them, I have found that a BRAIDED FISHING ROD SOCK fitted over the die and held in place by its bungee cord will catch 600 plus bullets into a plastic container, help drain excess oil/alcohol off the bullets, and keep the floor clean. When done, remove the rod sock, pour bullets onto a towel, and dry bullets, and store. By the way, you'll like the way your hands feel after the lanolin treatment. Unfortunately, you'll need to wash your hands..... because you've been around lead.

Lee precision products deliver good value to the money. I have a number of this type of Lee sizer kits and use them quite a lot. It works quick, it works well and it’s fast to use. I would give it five stars but this particular die sized bullets .0004 undersize. A couple of minutes of work corrected that problem.

Until recently, I was shooting Speer cast bullets from my 1911 target gun, but these are a much more economical way to produce lots of high quality projectiles. Once the molds are up to temperature, they produce very good bullets and the sprue cutter works perfectly for me. The harder alloys are somewhat harder to do, but that's to be expected. I've heard people complain about the lack of handles with the mold. I think it's an advantage. If each mold set came with handles, the price would be higher per set. By having one set of handles and multiple molds, storage is less of an issue and the overall cost is much lower.

These are very good sizing dies. I'm not crazy about the way Lee Precision designed the plastic case. When it's full, you can't pick it up off of the sizing die, without dropping several sized bullets, on the floor. To avoid that aggravation, pick up an old single stage press, and mount it upside down. Insert the die, from the bottom and place a container under it. You can then just drop the bullet into the die, and using the press, run it down through the die, allowing it to drop into the container below.

Great product great Quality

Produto de qualidade como toda linha Lee precision

For what it is intended

Nulla da dire: è il classico resizing kit della Lee e fa il suo dovere. Sicuramente prodotto originale e abbinato ad una pressa qualsiasi è molto efficace. Ricordarsi sempre di lubrificare le palle da trafilare (Alox o altro).

works with powder coated bullets, just run powder coated bullets though it and you're ready to load.

Ottimo, fa egregiamente il suo lavoro, arrivato prima della data stabilita.